Send Email
Send SMS
Search
Advanced Technocracy Inc.
Advanced Technocracy Inc.


Chemical Reaction Engineering Lab Equipment

Our product range includes a wide range of isothermal semi-batch reactor, chemical reactor service unit, computer controlled chemical reactor service unit, rtd studies in packed bed reactor, isothermal semi batch reactor and computer controlled isothermal semi batch reactor.

Isothermal Semi-Batch Reactor

REQUEST CALLBACK

Isothermal Semi-Batch Reactor
Ask for Price

Thanks for Contacting Us.

Product Details:
BrandAtico
MaterialStainless Steel

Isothermal Semi-Batch Reactor (Peristaltic Pump Feed System)

Description:

A isothermal semi-batch reactor is a semi-closed system with one input stream. It is operated under conditions like Isothermal (Temperature of Reaction Mass remains constant) and perfectly mixed (composition of reaction mixture is uniform throughout). This set-up is used to study a non-catalytic homogeneous reaction under isothermal condition.  

Utilities Required:

  • Electricity Supply: Single Phase, 220 V AC, 50 Hz, 5-15 Amp combined socket with earth connection. Earth voltage should be less than 5 volts.
  • Water supply and drain.
  • Instruments, Laboratory wares and Chemicals required for analysis as per the system adopted.   

Technical Details:

  • Reactor : Material Stainless Steel, Capacity 3.0 Ltrs. (approx).
  • Water Bath : Material Stainless Steel, Double wall, insulated with Ceramic wool.
  • Heater : Nichrome wire Heater
  • Stirrer : Material Stainless Steel Impeller and shaft coupled with FHP motor
  • Feed Tank (1Nos.) : Material Stainless Steel, Capacity 20 Ltrs.
  • Flow Measurement : Peristaltic Pumps, 2Nos. (One each for reactants).
  • Piping : Material Stainless Steel and Silicon Pipe.
  • Temp. Sensor : RTD PT-100 type
  • Control panel comprises of :
  • Digital Temp. Controller : PID Controller 0-199.9°C (For Water Bath)

 

Yes! I am Interested

Chemical Reactor Service Unit

REQUEST CALLBACK

Chemical Reactor Service Unit
Ask for Price

Thanks for Contacting Us.

Product Details:
BrandATICO
Materialss

 

Chemical Reactor Service Unit (With Data Logging Facility)

Description:

This set-up is designed to conduct experiments on different types of chemical reactors on the same service unit. Different types of reactors i.e. Continuously Stirred Tank Reactor (CSTR), Plug Flow Tubular Reactor (Coiled Tube Type) and Batch Reactor (which will be supplied on extra cost) as separate units can be installed on the service unit individually one at a time for conducting experiments. Basically this range of small-scale chemical reactors represents the most common types of chemical reactor found in industry. The reactors use the saponification reaction between ethyl acetate and sodium hydroxide. This provides a well-understood and safe reaction for the students to investigate the different reactor types.

Utilities Required:

  • Electricity Supply: Single Phase, 220 V AC, 50 Hz, 5-15 Amp combined socket with earth connection. Earth voltage should be less than 5 volts.
  • Water Supply & drain.
  • Floor Area: 2.0 m x 1.0 m
  • Instruments, Laboratory Glassware and Chemicals required for analysis as per the system adopted.
  • Computer System: i-3 processor with DVD Drive, Windows 7/8, MS-Office pre-loaded. One USB slot required in PC for Data Acquisition Card.  

Technical Details:

  • Feed Tanks : 2Nos. Capacity 5 Ltrs. (each)
  • Feed Circulation : By Peristaltic Pump (2Nos.)
  • Temperature Controller : PID Controller, 0-199.9ºC
  • Heater : Nichrome wire Heater.
  • Hot water Circulator : With water tank and pump to circulate water.
  • Product Analysis : By using Electronic Sensor, Output 4-20 mA.
  • Temperature Measurement : By Temperature Transmitter, RTD PT-100 Type.
  • Output 4-20 mA.
  • Piping : Stainless steel & Silicon pipe.

 

Yes! I am Interested

Chemical Reactor Service Unit

REQUEST CALLBACK

Chemical Reactor Service Unit
Ask for Price

Thanks for Contacting Us.

Product Details:
BrandAtico
Capacity (Litre)5 litre
Material of ConstructionStainless Steel

Chemical Reactor Service Unit (Peristaltic Pump Feed System)

Description:

Each reactor, mounted on a base plate can be attached to the service unit. The appropriate services such as feed circulation, instrumentation for and temperature measurement are connected to the reactor, and it then becomes operational. This service unit comprises feed tanks, peristaltic pumps for feed circulation & measurement etc. These all things are mounted on a compact and well-designed base for bench mounting. This is self-contained bench top service unit to accommodate the reactors, one at a time, for conducting experiments on the same unit. This set-up is designed to conduct experiments on different types of chemical reactors on the same service unit. Different types of reactors i.e. Continuously Stirred Tank Reactor (CSTR), Plug Flow Tubular Reactor (Coiled Tube Type) and Batch Reactor (which will be supplied on extra cost) as separate units can be installed on the service unit individually one at a time for conducting experiments. Basically this range of small-scale chemical reactors represents the most common types of chemical reactor found in industry. The reactors use the saponification reaction between ethyl acetate and sodium hydroxide. This provides a well-understood and safe reaction for the students to investigate the different reactor types.

Utilities Required:

  • Electricity Supply: Single Phase, 220 V AC, 50 Hz, 5-15 Amp combined socket with earth connection. Earth voltage should be less than 5 volts.
  • Water Supply.
  • Floor Drain.
  • Floor Area: 2.0 m x 1.0 m
  • Instruments, Laboratory Glassware and Chemicals required for analysis as per the system adopted..

Technical Details:

  • Feed Tanks : 2 Nos. (One each for each reactant)
  • Material : SS
  • Capacity : 5 Ltrs. Each.
  • Feed Circulation : By Peristaltic Pump (2Nos.)
  • Temperature Controller : PID Controller, 0-199.9ºC
  • Heater : Nichrome wire Heater.
  • Hot water Circulator : With water tank and pump to circulate water.
  • Temperature Sensor : RTD PT-100 Type.
  • Piping : Stainless steel & Silicon pipe.

Yes! I am Interested

Chemical Reactor Service Unit

REQUEST CALLBACK

Chemical Reactor Service Unit
Ask for Price

Thanks for Contacting Us.

Product Details:
BrandAtico
Capacity5 litre
Material of ConstructionStainless Steel
Volume (Litre)5 litre

Chemical Reactor Service Unit (Compressed Air Feed System)

Description:

The appropriate services such as feed circulation, instrumentation for and temperature measurement are connected to the reactor, and it then becomes operational. This service unit comprises feed tanks, rotameters for flow measurement of reactant etc. Compressed air is used for feed circulation. These all things are mounted on a compact and well-designed base for bench mounting. This is self-contained bench top service unit to accommodate the reactors, one at a time, for conducting experiments on the same unit. This set-up is designed to conduct experiments on different types of chemical reactors on the same service unit. Different types of reactors i.e. Continuously Stirred Tank Reactor (CSTR), Plug Flow Tubular Reactor (Coiled Tube Type) and Batch Reactor (which will be supplied on extra cost) as separate units can be installed on the service unit individually one at a time for conducting experiments. Basically this range of small-scale chemical reactors represents the most common types of chemical reactor found in industry. The reactors use the saponification reaction between ethyl acetate and sodium hydroxide. This provides a well-understood and safe reaction for the students to investigate the different reactor types. Each reactor, mounted on a base plate can be attached to the service unit.

Utilities Required:

  • Electricity Supply: Single Phase, 220 V AC, 50 Hz, 5-15 Amp combined socket with earth connection. Earth voltage should be less than 5 volts.
  • Compressed Air Supply: 2 CFM@1 bar
  • Water Supply.
  • Floor Drain.
  • Floor Area: 2.0 m x 1.0 m
  • Instruments, Laboratory Glassware and Chemicals required for analysis as per the system adopted.

Technical Details:

  • Feed Tanks : 2Nos. (One each for each reactant)
  • Material : Stainless Steel
  • Capacity : 5 Ltrs. Each.
  • Feed Circulation : By compressed air
  • Temperature Controller : PID Controller, 0-199.9ºC
  • Heater : Nichrome wire Heater.
  • Hot water Circulator : With water tank and pump to circulate water.
  • Temperature Sensor : RTD PT-100 Type.
  • Piping : Stainless steel & PU pipe.
  • Control panel comprises of:
  • With Standard make on/off switch, Mains Indicator etc.

 

Yes! I am Interested

Computer Controlled Chemical Reactor Service Unit

REQUEST CALLBACK

Computer Controlled Chemical Reactor Service Unit
Ask for Price

Thanks for Contacting Us.

Product Details:
BrandATICO
Materialss

Computer Controlled Chemical Reactor Service Unit (With Data Logging Facility)

Description:

The reactors use the saponification reaction between ethyl acetate and sodium hydroxide. This provides a well-understood and safe reaction for the students to investigate the different reactor types. Each reactor, mounted on a base plate can be attached to the service unit. The appropriate services such as feed circulation, instrumentation for temperature measurement & conductivity measurement for analysis are connected to the reactor, and it then becomes operational. This service unit comprises feed tanks, peristaltic pumps for feed circulation & Conductivity sensor for analysis. Flow of feed is controlled by computer signal. These all things are mounted on a compact and well-designed base for bench mounting. This is self-contained bench top service unit to accommodate the reactors, one at a time, for conducting experiments on the same unit. This set-up is designed to conduct experiments on different types of chemical reactors on the same service unit. Different types of reactors i.e. Continuously Stirred Tank Reactor (CSTR), Plug Flow Tubular Reactor (Coiled Tube Type) and Batch Reactor (which will be supplied on extra cost) as separate units can be installed on the service unit individually one at a time for conducting experiments. Basically this range of small-scale chemical reactors represents the most common types of chemical reactor found in industry.

Utilities Required:

  • Electricity Supply: Single Phase, 220 V AC, 50 Hz, 5-15 Amp combined socket with earth connection.
  • Earth voltage should be less than 5 volts.
  • Water Supply & drain.
  • Floor Area: 2.0 m x 1.0 m
  • Instruments, Laboratory Glassware and Chemicals required for analysis as per the system adopted.
  • Computer System: i-3 processor with DVD Drive, Windows 7/8, MS-Office pre-loaded. One USB slot required in PC for Data Acquisition Card.

Technical Details:

  • Feed Tanks : 2Nos. Capacity 5 Ltrs. (each)
  • Feed Circulation : By Peristaltic Pump, computer controlled for different RPM
  • Temperature Controller : PID Controller, 0-199.9ºC
  • Heater : Nichrome wire Heater.
  • Hot water Circulator : With water tank and pump to circulate water.
  • Product Analysis : By using Electronic Sensor, Output 4-20 mA.
  • Temperature Measurement : By Temperature Transmitter, RTD PT-100 Type.
  • Output 4-20 mA.
  • Piping : Stainless steel & Silicon pipe.
Yes! I am Interested

RTD Studies In Packed Bed Reactor

REQUEST CALLBACK

RTD Studies In Packed Bed Reactor
Ask for Price

Thanks for Contacting Us.

Product Details:
BrandAtico
MaterialBorosilicate Glass

RTD Studies In Packed Bed Reactor (Constant Head Feed System)

Description:

The setup consists of a glass column packed with Rasching Rings and one overhead feed tank. Water is fed to the reactor through liquid distributor, fitted at the bottom of the column. Rotameter is provided to measure the flow of water. The flow rate can be adjusted by operating the needle valve provided on Rotameter. For understanding the R.T.D. characteristics, a special arrangement to inject tracer into the lower end of reactor, using a syringe, is provided. Samples can be taken periodically from the top outlet of reactor. Axial diffusion and dispersion of fluid in packed beds are important for design and operation of separation equipment and Chemicals reactors. The tracer technique, the most widely used method for the study of axial dispersion. In stimulus response experimentation, we perturb the system using pulse input of tracer and then see how the system reacts or responds to this stimulus. The analysis of the response gives the desired information about the system.

Utilities Required:

  • Electricity Supply: Single Phase, 220 V AC, 50 Hz, 5-15 Amp combined socket with earth connection. Earth voltage should be less than 5 volts.
  • Instruments, Laboratory Glassware and Chemicals required for analysis as per the system adopted.

Technical Details:

  • Reactor Column : Material Borosilicate Glass
  • Packing : Rasching Rings, Material Borosilicate Glass.
  • Size 8-10mm (approx)
  • Feed Tank : Material Stainless Steel, Capacity 20 Ltrs.
  • Feed Circulation : By Polypropylene magnetic pump
  • Flow Measurement : Rotameter.
  • Piping : Stainless Steel and PVC/PU pipe.
  • Stop Watch : Electronic
    Yes! I am Interested

    Isothermal Semi Batch Reactor

    REQUEST CALLBACK

    Isothermal Semi Batch Reactor
    Ask for Price

    Thanks for Contacting Us.

    Product Details:
    BrandAtico
    MaterialStainless Steel

    Isothermal Semi Batch Reactor (Peristaltic Pump Feed System)

    Description:

    A isothermal semi-batch reactor is a semi-closed system with one input stream. It is operated under conditions like Isothermal (Temperature of Reaction Mass remains constant) and perfectly mixed (composition of reaction mixture is uniform throughout). This set-up is used to study a non-catalytic homogeneous reaction under isothermal condition.

    Utilities Required:

    • Electricity Supply: Single Phase, 220 V AC, 50 Hz, 5-15 Amp combined socket with earth connection. Earth voltage should be less than 5 volts.
    • Water supply and drain.
    • Instruments, Laboratory wares and Chemicals required for analysis as per the system adopted..  

    Technical Details:

    • Reactor : Material Stainless Steel, Capacity 3.0 Ltrs. (approx).
    • Water Bath : Material Stainless Steel, Double wall, insulated with Ceramic wool.
    • Heater : Nichrome wire Heater
    • Stirrer : Material Stainless Steel Impeller and shaft coupled with FHP motor
    • Feed Tank (1Nos.) : Material Stainless Steel, Capacity 20 Ltrs.
    • Flow Measurement : Peristaltic Pumps, 2Nos. (One each for reactants).
    • Piping : Material Stainless Steel and Silicon Pipe.
    • Temp. Sensor : RTD PT-100 type
    • Control panel comprises of :
    • Digital Temp. Controller : PID Controller 0-199.9°C (For Water Bath)

     

    Yes! I am Interested

    Computer Controlled Isothermal Semi batch Reactor

    REQUEST CALLBACK

    Computer Controlled Isothermal Semi batch Reactor
    Ask for Price

    Thanks for Contacting Us.

    Product Details:
    MaterialStainless steel

    Computer Controlled Isothermal Semi batch Reactor (With Data Logging Facility)

    Description:

    The set up consists of a Reactor fitted in a constant temperature water bath. Before starting the reaction the reactor is charged with measured quantity of one reactant. From a feed tank another reactant is fed to the reactor. Peristaltic Pump is provided to measure the flow of Chemical. One stirrer is fitted for mixing the reactants in reactor and other is fitted in water bath to keep the uniform temperature throughout in the bath. The temperature of bath can be maintained from ambient to 70°C with the help of Digital Temperature indicator Cum Controller. A isothermal semi-batch reactor is a semi-closed system with one input stream. It is operated under conditions like Isothermal (Temperature of Reaction Mass remains constant) and perfectly mixed (composition of reaction mixture is uniform throughout). This set-up is used to study a non-catalytic homogeneous reaction under isothermal condition.

    Utilities Required:

    • Electricity Supply: Single Phase, 220 V AC, 50 Hz, 5-15 Amp combined socket with earth connection. Earth voltage should be less than 5 volts.
    • Water Supply & Drain
    • Instruments, Laboratory wares and Chemicals required for analysis as per the system adopted.
    • Computer System: i-3 processor with DVD Drive, Windows 7/8, MS-Office pre-loaded. One USB slot required in PC for Data Acquisition Card.   

    Technical Details:

    • Reactor : Material Stainless Steel, Capacity 2 Ltrs. (approx).
    • Water Bath : Material Stainless Steel, Double wall, insulated with Ceramic Wool.
    • Heater : Nichrome wire Heater with Control Unit to control heat input.
    • Stirrer : Material Stainless Steel Impeller and shaft coupled with FHP motor
    • Feed Tank (1Nos.) : Material Stainless Steel, Capacity - 20 Ltrs.
    • Feed Circulation : By Peristaltic Pump (1No.), Computer controlled for different RPM
    • Piping : Stainless Steel and Silicon pipe.
    • Product Analysis : By using Electronic Sensor, Output 4-20 mA.
    • Temp. Measurement : Temperature transmitter (1No.), 0-199.9°C
    • Control panel comprises of :
    • Digital Temp. Controller : PID Controller, 0-199.9°C, (For Water Bath)

     

    Yes! I am Interested

    Combined Flow Reactor

    REQUEST CALLBACK

    Combined Flow Reactor
    Ask for Price

    Thanks for Contacting Us.

    Combined Flow Reactor (With Data Logging Facility)

    Description:

    This set-up is used to study a non-catalytic homogeneous second order liquid phase reaction under ambient condition in a combined reactor. It consists of two reactors connected in series, one is plug flow reactor and another mixed flow reactor. In an ideal Plug Flow Reactor (PFTR) there is no mixing in the direction of flow and complete mixing perpendicular to direction of flow. Concentration of reactants varies along the length of reactor but not in radial direction. In case of a coil turbulence is introduced due to frequent change in direction of flow and presence of secondary flow, so a higher value of reaction rate constant is expected in coil tube type plug flow reactor. The set up consists of two feed tanks through which two reactants are fed to the reactors fitted in series Peristaltic Pumps are provided to measure the individual flow of Chemicals. 1st is a helical coil tube type reactor made up of SS pipe. Reactants enter at lower end coming out of the top of coil from where it is fed to a MFR fitted with stirrer for proper mixing. Samples are collected for analysis.

    Utilities Required:

    • Electricity Supply: Single Phase, 220 V AC, 50 Hz, 5-15 Amp combined socket with earth connection. Earth voltage should be less than 5 volts.
    • Water Supply & drain
    • Instruments, Laboratory Glassware and Chemicals required for analysis as per the system adopted.
    • Computer System: i3 processor with DVD Drive, Windows 7/8, MS-Office pre-loaded. One USB slot required in PC for Data Acquisition Card..  

     

    Technical Details:

    • 1st Reactor : Material Stainless Steel, Capacity (0.6-0.7) Ltrs. (approx.) (Helical Coiled Tube Type)
    • 2nd Reactor : Material Stainless Steel, Capacity 2 Ltrs (approx.).
    • Stirrer for MFR : Stainless Steel Impeller and shaft coupled with FHP motor
    • Feed Tank (2Nos.) : Material Stainless Steel, Capacity 20 Ltrs.
    • Flow Measurement : Peristaltic Pumps, 2Nos. (One each for Reactants)
    • Product Analysis : By Electronic Sensor, Output 4-20 mA.
    • Piping : Stainless Steel and Silicon pipe

     

    Yes! I am Interested

    Packed Bed Reactor

    REQUEST CALLBACK

    Packed Bed Reactor
    Ask for Price

    Thanks for Contacting Us.

    Product Details:
    BrandATICO
    MaterialBorosilicate Glass

    Packed Bed Reactor (Compressed Air Feed System)

    Description:

    The setup consists of a glass column packed with Rasching Rings and two feed tanks. Reactants are fed to the reactor through liquid distributor, fitted at the bottom of the column. Rotameters are provided to measure the individual flow of Chemicals. The flow rate can be adjusted by operating the needle valves provided on respective Rotameter. The compressed air is used for circulation of feed. Samples can be taken periodically from the top outlet of reactor. Pressure Regulator & Pressure Gauge are fitted in the compressed air line.

    Utilities Required:

    • Compressed Air Supply: 0.5 CFM@1 bar
    • Water Supply.
    • Floor Drain.
    • Floor Area Required : 1.0 m x 1.0 m.
    • Instruments, Laboratory Glassware and Chemicals required for analysis as per the system adopted.

    Technical Details:

    • Reactor Column : Material Borosilicate Glass Volume 1.2 Ltrs. (Approx).
    • Packing : Rasching Rings, Material Borosilicate Glass.
    • Size 6-8 mm (approx)
    • Feed Tank (2Nos.) : Material Stainless Steel, Capacity 20 Ltrs.
    • Feed Circulation : By compressed air.
    • Flow Measurement : Rotameter 2Nos. (One each for Reactants).
    • Piping : Stainless Steel and PU Pipe.
    • Pressure Regulator : 0-2 Kg/cm2
    • Pressure Gauge : Bourdon type 0-2 Kg/cm2

     

      Yes! I am Interested

      Packed Bed Reactor

      REQUEST CALLBACK

      Packed Bed Reactor
      Ask for Price

      Thanks for Contacting Us.

      Product Details:
      BrandAtico
      Capacity 1.2 Ltrs
      MaterialBorosilicate Glass
      Material of Construction Borosil Glass
      Power (Kw)220 V AC, 50 Hz, 5-15 Amp
      Tank Capacity (Litre)20 Ltr
      Voltage (V)less than 5 volts
      Volume (Litre)1.2 Ltrs

      Packed Bed Reactor (Peristaltic Pump Feed System)

      Description:

      The setup consists of a glass column packed with Rasching Rings and two feed tanks. Reactants are fed to the reactor through liquid distributor, fitted at the bottom of the column. Peristaltic pumps are provided to measure the individual flow of Chemicals. The flow rate can be adjusted by operating respective Peristaltic pumps. Samples can be taken periodically from the top outlet of reactor.

      Utilities Required:

      • Electricity Supply: Single Phase, 220 V AC, 50 Hz, 5-15 Amp combined socket with earth connection. Earth voltage should be less than 5 volts.
      • Water Supply.
      • Floor Drain.
      • Instruments, Laboratory Glassware and Chemicals required for analysis as per the system adopted.

      Technical Details:

      • Reactor Column : Material Borosilicate Glass
      • Volume 1.2 Ltrs. (approx).
      • Packing : Rasching Rings, Material Borosilicate Glass.
      • Size 6-8 mm (approx)
      • Feed Tank (2Nos.) : Material Stainless Steel, Capacity 20 Ltrs.
      • Feed Circulation : By Peristaltic Pump (2Nos.)
      • Piping : Stainless Steel and Silicon Pipe.
      • Stop Watch : Electronic.
      Yes! I am Interested

      Isothermal Semi Batch Reactor

      REQUEST CALLBACK

      Isothermal Semi Batch Reactor
      Ask for Price

      Thanks for Contacting Us.

      Product Details:
      BrandATICO
      MaterialStainless steel
      Power (W)220 V AC, 50 Hz, 5-15 Am

      Isothermal Semi Batch Reactor (Constant Head Feed System)

      Description:

      The set up consists of a Reactor fitted in a constant temperature water bath. Before starting the reaction the reactor is charged with measured quantity of one reactant. From a overhead feed tank another reactant is fed to the reactor. Using a sampling pipette samples can be taken out for analysis after fixed interval. Rotameter is provided to measure the flow of reactants. One stirrer is fitted for mixing the reactants in reactor and other is fitted in water bath to keep the uniform temperature throughout in the bath. The temperature of bath can be maintained from ambient to 70°C with the help of Digital Temperature indicator Cum Controller. A isothermal semi-batch reactor is a semi-closed system with one input stream. It is operated under conditions like Isothermal (Temperature of Reaction Mass remains constant) and perfectly mixed (composition of reaction mixture is uniform throughout). This set-up is used to study a non-catalytic homogeneous reaction under isothermal condition.

      Utilities Required:

      • Electricity Supply: Single Phase, 220 V AC, 50 Hz, 5-15 Amp combined socket with earth connection. Earth voltage should be less than 5 volts.
      • Water Supply
      • Floor Drain.
      • Instruments, Laboratory wares and Chemicals required for analysis as per the system adopted.

      Technical Details:

      • Reactor : Material Stainless Steel, Capacity 2 Ltrs. (approx).
      • Water Bath : Material Stainless Steel, Double wall,
      • Insulated with Ceramic Wool.
      • Heater : Nichrome wire Heater
      • Agitator : Material Stainless Steel Impeller and shaft coupled with FHP motor
      • Impeller : Material Stainless Steel, 4 square bladed (1 No.)
      • Baffles : Material Stainless Steel,(4Nos.) Detachable, symmetrically placed
      • Feed Tank (1No.) : Material Stainless Steel, Capacity - 20 Ltrs.
      • Feed Circulation : By Polypropylene magnetic pump.
      • Flow Measurement : Rotameter.
      • Piping : Material Stainless Steel and PVC/PU pipe.
      • Stop Watch : Electronic
      • Temp. Sensor : RTD PT-100 type
      Yes! I am Interested

      Computer Controlled Combined Flow Reactor

      REQUEST CALLBACK

      Computer Controlled Combined Flow Reactor
      Ask for Price

      Thanks for Contacting Us.

      Product Details:
      BrandAtico
      MaterialStainless Steel

      Computer Controlled Combined Flow Reactor (With Data Logging Facility)

      Description:

      This set-up is used to study a non-catalytic homogeneous second order liquid phase reaction under ambient condition in a combined reactor. It consists of two reactors connected in series, one is plug flow reactor and another mixed flow reactor. In an ideal Plug Flow Reactor (PFTR) there is no mixing in the direction of flow and complete mixing perpendicular to direction of flow. Concentration of reactants varies along the length of reactor but not in radial direction. In case of a coil turbulence is introduced due to frequent change in direction of flow and presence of secondary flow, so a higher value of reaction rate constant is expected in coil tube type plug flow reactor. The set up consists of two feed tanks through which two reactants are fed to the reactors fitted in series Peristaltic Pumps are provided to measure the individual flow of Chemicals. 1st is a helical coil tube type reactor made up of SS pipe. Reactants enter at lower end coming out of the top of coil from where it is fed to a MFR fitted with stirrer for proper mixing. Samples are collected for analysis.

      Utilities Required:

      • Electricity Supply: Single Phase, 220 V AC, 50 Hz, 5-15 Amp combined socket with earth connection. Earth voltage should be less than 5 volts.
      • Water Supply & drain
      • Instruments, Laboratory Glassware and Chemicals required for analysis as per the system adopted.
      • Computer System: i3 processor with DVD Drive, Windows 7/8, MS-Office pre-loaded. One USB slot required in PC for Data Acquisition Card..  

      Technical Details:

      • 1st Reactor : Material Stainless Steel, Capacity (0.6-0.7) Ltrs. (approx)(Helical Coiled Tube Type)
      • 2nd Reactor : Material Stainless Steel, Capacity 2 Ltrs (approx).
      • Stirrer for MFR : Stainless Steel Impeller and shaft coupled with FHP motor
      • Feed Tank (2Nos.) : Material Stainless Steel, Capacity 20 Ltrs.
      • Feed circulation : By Peristaltic Pump (2 Nos.), Computer controlled for different RPM
      • Product Analysis : By Electronic Sensor, Output 4-20 mA.
      • Piping : Stainless Steel and Silicon pipe

       

      Yes! I am Interested

      Computer Controlled Packed Bed Reactor

      REQUEST CALLBACK

      Computer Controlled Packed Bed Reactor
      Ask for Price

      Thanks for Contacting Us.

      Product Details:
      BrandAtico
      MaterialBorosilicate Glass

      Computer Controlled Packed Bed Reactor (With Data Logging Facility)

      Description:

      The setup consists of a glass column packed with Rasching Rings and two feed tanks. Reactants are fed to the reactor through liquid distributor, fitted at the bottom of the column. Peristaltic Pumps are provided to measure the individual flow of Chemicals. The flow rate can be adjusted by operating the respective Peristaltic Pump.

      Utilities Required:

      • Electricity Supply: Single Phase, 220 V AC, 50 Hz, 5-15 Amp combined socket with earth connection. Earth voltage should be less than 5 volts.
      • Water Supply & drain
      • Instruments, Laboratory Glassware and Chemicals required for analysis as per the system adopted.
      • Computer System: i-3 processor with DVD Drive, Windows 7/8, MS-Office pre-loaded. One USB slot required in PC for Data Acquisition Card..

      Technical Details:

      • Reactor Column : Material Borosilicate Glass, Volume 1.2 Ltrs. (approx).
      • Packing : Rasching Rings, Material Borosilicate Glass.
      • Size 6-8 mm (approx.)
      • Feed Tank (2Nos.) : Material Stainless Steel, Capacity 20 Ltrs.
      • Feed Circulation : By Peristaltic Pump (2Nos.)
      • Computer controlled for different RPM
      • Piping : Stainless Steel and Silicon pipe.
      • Product Analysis : By Electronic Sensor, Output 4-20 mA.
      Yes! I am Interested

      Combined Flow Reactor

      REQUEST CALLBACK

      Combined Flow Reactor
      Ask for Price

      Thanks for Contacting Us.

      Product Details:
      BrandAtico
      MaterialStainless Steel

      Combined Flow Reactor (Constant Head Feed System)

      Description:

      This set-up is used to study a non-catalytic homogeneous second order liquid phase reaction under ambient condition in a combined reactor. It consists of two reactors connected in series, one is plug flow reactor and another mixed flow reactor. In an ideal Plug Flow Reactor (PFTR) there is no mixing in the direction of flow and complete mixing perpendicular to direction of flow. Concentration of reactants varies along the length of reactor but not in radial direction. In case of a coil turbulence is introduced due to frequent change in direction of flow and presence of secondary flow, so a higher value of reaction rate constant is expected in coil tube type plug flow reactor. The set up consists of two overhead feed tanks through which two reactants are fed to the reactors fitted in series. Rotameters are provided to measure the individual flow of Chemicals. The flow rate can be adjusted by operating the needle valves provided on respective Rotameter. 1st is a helical coil tube type reactor made up of SS pipe. Reactants enter at lower end coming out of the top of coil from where it is fed to a MFR fitted with stirrer for proper mixing.

      Utilities Required:

      • Electricity supply: Single phase, 220 VAC, 50 Hz, 5-15 Amp combined socket with earth connection. Earth voltage should be less than 5 volts.
      • Water Supply
      • Floor Drain
      • Instruments, Laboratory Glassware and Chemicals required for analysis as per the system adopted.  

      Technical Details:

      • 1st Reactor : Material Stainless Steel, Capacity (0.6-0.7) Ltrs. (approx.) (Helical Coiled Tube Type)
      • 2nd Reactor : Material Stainless Steel, Capacity 2 Ltrs (Approx).
      • Agitator : Material Stainless Steel Impeller and shaft coupled with FHP motor
      • Impeller : Material Stainless Steel, 4 square bladed (1 No.)
      • Baffles : Material Stainless Steel,(4Nos.) Detachable, symmetrically placed
      • Feed Tank (2Nos.) : Material Stainless Steel, Capacity 20 Ltrs. (approx.)
      • Feed Circulation : By Polypropylene magnetic pump
      • Flow Measurement : Rotameter 2 Nos. (One each for Reactants).
      • Piping : Stainless Steel and PVC/PU pipe
      Yes! I am Interested

      Packed Bed Reactor

      REQUEST CALLBACK

      Packed Bed Reactor
      Ask for Price

      Thanks for Contacting Us.

      Product Details:
      BrandAtico
      MaterialBorosilicate Glass

      Packed Bed Reactor (Constant Head Feed System)

      Description:

      The setup consists of a glass column packed with Rasching Rings and two overhead feed tanks. Reactants are fed to the reactor through liquid distributor, fitted at the bottom of the column. Rotameters are provided to measure the individual flow of Chemicals. The flow rate can be adjusted by operating the needle valves provided on respective Rotameter. Samples can be taken periodically from the top outlet of reactor.

      Utilities Required:

      • Electricity Supply: Single Phase, 220 V AC, 50 Hz, 5-15 Amp combined socket with earth connection. Earth voltage should be less than 5 volts.
      • Water Supply.
      • Floor Drain.
      • Instruments, Laboratory Glassware and Chemicals required for analysis as per the system adopted.

      Technical Details:

      • Reactor Column : Material Borosilicate Glass Volume 1.2 Ltrs. (approx).
      • Packing : Rasching Rings, Material Borosilicate Glass.
      • Size 6-8 mm (approx)
      • Feed Tank (2Nos.) : Material Stainless Steel, Capacity 20 Ltrs.
      • Feed Circulation : By Polypropylene magnetic pump
      • Flow Measurement : Rotameter 2Nos. (One each for Reactants).
      • Piping : Stainless Steel and PVC/PU pipe.
      Yes! I am Interested

      Packed Bed Reactor

      REQUEST CALLBACK

      Packed Bed Reactor
      Ask for Price

      Thanks for Contacting Us.

      Product Details:
      BrandATICO
      Capacity 1.2 Ltrs
      MaterialBorosilicate Glass,
      Material of ConstructionBorosil Glass
      Power (Kw)220 V AC, 50 Hz, 5-15 Amp
      Tank Capacity (Litre)20 Litre
      Voltage (V)less than 5 volt
      Voltage (Volt)less than 5 volts.
      Volume (Litre)1.2 Ltrs

      Packed Bed Reactor (With Data Logging Facility)

      Description:

      The setup consists of a glass column packed with Rasching Rings and two feed tanks. Reactants are fed to the reactor through liquid distributor, fitted at the bottom of the column. Peristaltic Pumps are provided to measure the individual flow of Chemicals. The flow rate can be adjusted by operating the respective Peristaltic Pump.

      Utilities Required:

      • Electricity Supply: Single Phase, 220 V AC, 50 Hz, 5-15 Amp combined socket with earth connection. Earth voltage should be less than 5 volts.
      • Water Supply & drain
      • Instruments, Laboratory Glassware and Chemicals required for analysis as per the system adopted.
      • Computer System: i-3 processor with DVD Drive, Windows 7/8, MS-Office pre-loaded. One USB slot required in PC for Data Acquisition Card.

      Technical Details:

      • Reactor Column : Material Borosilicate Glass, Volume 1.2 Ltrs. (approx).
      • Packing : Rasching Rings, Material Borosilicate Glass. Size 6-8 mm (approx)
      • Feed Tank (2Nos.) : Material Stainless Steel, Capacity 20 Ltrs.
      • Feed Circulation : By Peristaltic Pump (2Nos.)
      • Product Analysis : By using Electronic Sensor, Output 4-20 mA.
      • Piping : Stainless/Silicon pipe
      Yes! I am Interested

      RTD Studies In Packed Bed Reactor

      REQUEST CALLBACK

      RTD Studies In Packed Bed Reactor
      Ask for Price

      Thanks for Contacting Us.

      Product Details:
      BrandAtico
      MaterialBorosilicate Glass

      RTD Studies In Packed Bed Reactor (Peristaltic Pump Feed System)

      Description:

      The setup consists of a glass column packed with Rasching Rings and one feed tank. Water is fed to the reactor through liquid distributor, fitted at the bottom of the column. Peristaltic Pump is provided to measure the flow of water. For understanding the R.T.D. characteristics, a special arrangement to inject tracer into the lower end of reactor, using a syringe, is provided. Samples can be taken periodically from the top outlet of reactor. Axial diffusion and dispersion of fluid in packed beds are important for design and operation of separation equipment and Chemicals reactors. The tracer technique, the most widely used method for the study of axial dispersion. In stimulus response experimentation, we perturb the system using pulse input of tracer and then see how the system reacts or responds to this stimulus. The analysis of the response gives the desired information about the system.

      Utilities Required:

      • Electricity Supply: Single Phase, 220 V AC, 50 Hz, 5-15 Amp combined socket with earth connection. Earth voltage should be less than 5 volts.
      • Water Supply.
      • Floor Drain.
      • Instruments, Laboratory Glassware and Chemicals required for analysis as per the system adopted.

      Technical Details:

      • Reactor Column : Material Borosilicate Glass capacity 1.2 Ltrs (approx.)
      • Packing : Rasching Rings, Material Borosilicate Glass.
      • Size 8-10mm (approx)
      • Feed Tank : Material Stainless Steel, Capacity 20 Ltrs.
      • Piping : Stainless Steel and Silicon Pipe.
      • Flow Measurement : Peristaltic Pumps, 1No. (For water).
      • Stop Watch : Electronic 

       

        Yes! I am Interested

        RTD Studies In Packed Bed Reactor

        REQUEST CALLBACK

        RTD Studies In Packed Bed Reactor
        Ask for Price

        Thanks for Contacting Us.

        Product Details:
        BrandAtico
        MaterialBorosilicate Glass

        RTD Studies In Packed Bed Reactor (Compressed Air Feed System)

        Description:

        The setup consists of a glass column packed with Rasching Rings and one feed tank. Water is fed to the reactor through liquid distributor, fitted at the bottom of the column. Rotameter is provided to measure the flow of water. The flow rate can be adjusted by operating the needle valve provided on Rotameter. For understanding the R.T.D. characteristics, a special arrangement to inject tracer into the lower end of reactor, using a syringe, is provided. Samples can be taken periodically from the top outlet of reactor. Pressure Regulator & Pressure Gauge are fitted in the compressed air line.

        Axial diffusion and dispersion of fluid in packed beds are important for design and operation of separation equipment and Chemicals reactors. The tracer technique, the most widely used method for the study of axial dispersion. In stimulus response experimentation, we perturb the system using pulse input of tracer and then see how the system reacts or responds to this stimulus. The analysis of the response gives the desired information about the system.

        Utilities Required:

        • Compressed Air Supply: 0.25 CFM@1 bar
        • Water Supply.
        • Floor Drain.
        • Floor Area Required : 1.0 m x 1.0 m.
        • Instruments, Laboratory Glassware and Chemicals required for analysis as per the system adopted.

        Technical Details:

        • Reactor Column : Material Borosilicate Glass
        • Packing : Rasching Rings, Material Borosilicate Glass.
        • Size 8-10mm (approx)
        • Feed Tank : Material Stainless Steel, Capacity 20 Ltrs.
        • Feed Circulation : By compressed air.
        • Flow Measurement : Rotameter.
        • Piping : Stainless Steel and PU pipe.
        • Pressure Regulator : 0-2 Kg/cm2
        • Pressure Gauge : Bourdon type 0-2 Kg/cm2
        • Stop Watch : Electronic

         

        Yes! I am Interested

        Chemical Reactor Service Unit

        REQUEST CALLBACK

        Chemical Reactor Service Unit
        Ask for Price

        Thanks for Contacting Us.

        Product Details:
        BrandATICO
        Materialss

        Chemical Reactor Service Unit (With Data Logging Facility)

        Description:

        This set-up is designed to conduct experiments on different types of chemical reactors on the same service unit. Different types of reactors i.e. Continuously Stirred Tank Reactor (CSTR), Plug Flow Tubular Reactor (Coiled Tube Type) and Batch Reactor (which will be supplied on extra cost) as separate units can be installed on the service unit individually one at a time for conducting experiments. Basically this range of small-scale chemical reactors represents the most common types of chemical reactor found in industry. The reactors use the saponification reaction between ethyl acetate and sodium hydroxide. This provides a well-understood and safe reaction for the students to investigate the different reactor types.

        Utilities Required:

        • Electricity Supply: Single Phase, 220 V AC, 50 Hz, 5-15 Amp combined socket with earth connection. Earth voltage should be less than 5 volts.
        • Water Supply & drain.
        • Floor Area: 2.0 m x 1.0 m
        • Instruments, Laboratory Glassware and Chemicals required for analysis as per the system adopted.
        • Computer System: i-3 processor with DVD Drive, Windows 7/8, MS-Office pre-loaded. One USB slot required in PC for Data Acquisition Card.

        Technical Details:

        • Feed Tanks : 2Nos. Capacity 5 Ltrs. (each)
        • Feed Circulation : By Peristaltic Pump (2Nos.)
        • Temperature Controller : PID Controller, 0-199.9ºC
        • Heater : Nichrome wire Heater.
        • Hot water Circulator : With water tank and pump to circulate water.
        • Product Analysis : By using Electronic Sensor, Output 4-20 mA.
        • Temperature Measurement : By Temperature Transmitter, RTD PT-100 Type.
        • Output 4-20 mA.
        • Piping : Stainless steel & Silicon pipe.
        Yes! I am Interested

        Computer Controlled RTD Studies In Packed Bed Reactor

        REQUEST CALLBACK

        Computer Controlled RTD Studies In Packed Bed Reactor
        Ask for Price

        Thanks for Contacting Us.

        Product Details:
        BrandAtico
        MaterialBorosilicate Glass

        Computer Controlled RTD Studies In Packed Bed Reactor (With Data Logging Facility)

        Description:

        The present set-up has a facility to interface the system with computer which enables to log the experimental data using computer. This software package provides a comprehensive educational software environment within which the investigations can be performed. This software is capable to tabulate the sample readings according to the requirement of experiment under study and results obtained can be compared. The real time data acquisition can be done by interfacing the set-up with computer using software. Software allows the user to have control on data logging, printing the stored data, preparing spread sheets in Excel etc. Axial diffusion and dispersion of fluid in packed beds are important for design and operation of separation equipment and Chemicals reactors. The tracer technique, the most widely used method for the study of axial dispersion. In stimulus response experimentation, we perturb the system using pulse input of tracer and then see how the system reacts or responds to this stimulus. The analysis of the response gives the desired information about the system. The setup consists of a glass column packed with Rasching Rings and one feed tank. Water is fed to the reactor through liquid distributor, fitted at the bottom of the column. Peristaltic Pump is provided to measure the flow of water. For understanding the R.T.D. characteristics, a special arrangement to inject tracer into the lower end of reactor, using a syringe, is provided. Samples can be taken periodically from the top outlet of reactor.

        Utilities Required:

        • Electricity Supply: Single Phase, 220 V AC, 50 Hz, 5-15 Amp combined socket with earth connection. Earth voltage should be less than 5 volts.
        • Water Supply & drain
        • Instruments, Laboratory Glassware and Chemicals required for analysis as per the system adopted.
        • Computer System: i-3 processor with DVD Drive, Windows 7/8, MS-Office pre-loaded. One USB slot required in PC for Data Acquisition Card.

        Technical Details:

        • Reactor Column : Material Borosilicate Glass capacity 1.2 Ltrs approx.
        • Packing : Rasching Rings, Material Borosilicate Glass.
        • Size 8-10mm (approx)
        • Feed Tank : Material Stainless Steel, Capacity - 20 Ltrs.
        • Piping : Stainless Steel and Silicon pipe
        • Flow Measurement : Peristaltic Pumps (1No)
        • Computer controlled for different RPM
        • Product Analysis : By using Electronic Sensor, Output 4-20 mA.
        Yes! I am Interested

        RTD Studies In Packed Bed Reactor

        REQUEST CALLBACK

        RTD Studies In Packed Bed Reactor
        Ask for Price

        Thanks for Contacting Us.

        Product Details:
        BrandAtico
        MaterialBorosilicate Glass

        RTD Studies In Packed Bed Reactor (With Data Logging Facility)

        Description:

        The present set-up has a facility to interface the system with computer which enables to log the experimental data using computer. This software package provides a comprehensive educational software environment within which the investigations can be performed. This software is capable to tabulate the sample readings according to the requirement of experiment under study and results obtained can be compared. The real time data acquisition can be done by interfacing the set-up with computer using software. Software allows the user to have control on data logging, printing the stored data, preparing spread sheets in Excel etc. Axial diffusion and dispersion of fluid in packed beds are important for design and operation of separation equipment and Chemicals reactors. The tracer technique, the most widely used method for the study of axial dispersion. In stimulus response experimentation, we perturb the system using pulse input of tracer and then see how the system reacts or responds to this stimulus. The analysis of the response gives the desired information about the system. The setup consists of a glass column packed with Rasching Rings and one feed tank. Water is fed to the reactor through liquid distributor, fitted at the bottom of the column. Peristaltic Pump is provided to measure the flow of water. For understanding the R.T.D. characteristics, a special arrangement to inject tracer into the lower end of reactor, using a syringe, is provided. Samples can be taken periodically from the top outlet of reactor. The present set-up has a facility to interface the system with computer which enables to log the experimental data using computer. This software package provides a comprehensive educational software environment within which the investigations can be performed. This software is capable to tabulate the sample readings according to the requirement of experiment under study and results obtained can be compared. The real time data acquisition can be done by interfacing the set-up with computer using software. Software allows the user to have control on data logging, printing the stored data, preparing spread sheets in Excel etc.

        Utilities Required:

        • Electricity Supply: Single Phase, 220 V AC, 50 Hz, 5-15 Amp combined socket with earth connection. Earth voltage should be less than 5 volts.
        • Water Supply & drain
        • Instruments, Laboratory Glassware and Chemicals required for analysis as per the system adopted.
        • Computer System: i-3 processor with DVD Drive, Windows 7/8, MS-Office pre-loaded. One USB slot required in PC for Data Acquisition Card.

        Technical Details:

        • Reactor Column : Material Borosilicate Glass capacity 1.2 Ltrs (approx.)
        • Packing : Rasching Rings, Material Borosilicate Glass.
        • Size 8-10mm (approx)
        • Feed Tank : Material Stainless Steel, Capacity 20 Ltrs.
        • Piping : Stainless Steel and Silicon pipe.
        • Flow Measurement : Peristaltic Pumps-1No. (for water).
        • Product Analysis : By using Electronic Sensor, Output 4-20 mA.
        Yes! I am Interested

        Isothermal Batch Reactor

        REQUEST CALLBACK

        Isothermal Batch Reactor
        Ask for Price

        Thanks for Contacting Us.

        Product Details:
        BrandAtico
        MaterialStainless Steel

        Isothermal Batch Reactor (With Data Logging Facility)

        Description:

        A batch reactor is a closed system with no input and output streams. A batch reactor can operate under conditions like Isothermal (Temperature of Reaction Mass remains constant), perfectly mixed (composition of reaction mixture is uniform throughout), and constant volume (volume of the reaction mixture within the reactor remains constant, there is no appreciable change in the density of reaction mass). This setup is used to study a non-catalytic homogeneous reaction under isothermal condition.The set up consists of a Reactor fitted in a constant temperature water bath. One stirrer is fitted for mixing the reactants in reactor and other is fitted in water bath to keep the uniform temperature throughout in the bath. The temperature of bath can be maintained from ambient to 90°C with the help of Digital Temperature indicator Cum Controller.

        Utilities Required:

        • Electricity Supply: Single Phase, 220 V AC, 50 Hz, 5-15 Amp combined socket with earth connection.
        • Earth voltage should be less than 5 volts.
        • Water Supply.
        • Floor Drain.
        • Instruments, Laboratory Glassware and Chemicals required for analysis as per the system adopted.
        • Computer System: i-3 processor with DVD Drive, Windows 7/8, MS-Office pre-loaded. One USB slot required in PC for Data Acquisition Card.   

        Technical Details:

        • Reactor : Material Stainless Steel, Volume- 2 Ltrs. (Approx.)
        • Water Bath : Material Stainless Steel, Double wall, insulated with Ceramic Wool.
        • Heater : Nichrome wire Heater
        • Agitator : Material Stainless Steel Impeller and shaft coupled with FHP motor
        • Stirrer : Stainless Steel Impeller and shaft coupled with FHP motor.
        • Product Analysis : By using Electronic Sensor, Output 4-20 mA.
        • Temp. Measurement : Temperature transmitter-1No. RTD PT-100 type
        • Control panel comprises of :
        • Digital Temp. Controller : PID Controller, 0-199.9°C, (For Water Bath) 
        Yes! I am Interested

        Chemical Reactor Service Unit

        REQUEST CALLBACK

        Chemical Reactor Service Unit
        Ask for Price

        Thanks for Contacting Us.

        Product Details:
        BrandATICO
        Capacity5 litre
        MaterialSS
        Material of ConstructionStainless Steel
        Volume (Litre)5 litre

        Chemical Reactor Service Unit (Constant Head Feed System)

        Description:

        This set-up is designed to conduct experiments on different types of chemical reactors on the same service unit. Different types of reactors i.e. Continuously Stirred Tank Reactor (CSTR), Plug Flow Tubular Reactor (Coiled Tube Type) and Batch Reactor (which will be supplied on extra cost) as separate units can be installed on the service unit individually one at a time for conducting experiments. Basically this range of small-scale chemical reactors represents the most common types of chemical reactor found in industry. The reactors use the saponification reaction between ethyl acetate and sodium hydroxide. This provides a well-understood and safe reaction for the students to investigate the different reactor types..

        Utilities Required:

        • Electricity Supply: Single Phase, 220 V AC, 50 Hz, 5-15 Amp combined socket with earth connection. Earth voltage should be less than 5 volts.
        • Water Supply.
        • Floor Drain.
        • Floor Area: 2.0 m x 1.0 m
        • Instruments, Laboratory Glassware and Chemicals required for analysis as per the system adopted.   

        Technical Details:

        • Feed Tanks : 2 Nos. (One each for each reactant)
        • Material : Stainless Steel
        • Capacity : 5 Ltrs. Each.
        • Feed Circulation : By pumps-2Nos. (One each for each reactant)
        • Temperature Controller : PID Controller, 0-199.9ºC
        • Heater : Nichrome wire Heater.
        • Hot water Circulator : With water tank and pump to circulate water.
        • Temperature Sensor : RTD PT-100 Type.
        • Piping : Stainless steel & PVC pipe.

         

        Yes! I am Interested

        Isothermal Batch Reactor

        REQUEST CALLBACK

        Isothermal Batch Reactor
        Ask for Price

        Thanks for Contacting Us.

        Product Details:
        BrandAtico
        MaterialStainless Steel

        Description:

        A batch reactor is a closed system with no input and output streams. A batch reactor can operate under conditions like Isothermal (Temperature of Reaction Mass remains constant), perfectly mixed (composition of reaction mixture is uniform throughout), and constant volume (volume of the reaction mixture within the reactor remains constant, there is no appreciable change in the density of reaction mass). This set-up is used to study a non-catalytic homogeneous reaction under isothermal condition. Samples can be taken out with the help of a sampling pipette.

        Utilities Required:

        • Electricity Supply: Single Phase, 220 V AC, 50 Hz, 5-15 Amp combined socket with earth connection. Earth voltage should be less than 5 volts.
        • Water Supply.
        • Floor Drain.
        • Floor Area Required: 1.0 m x 0.5 m
        • Instruments, Laboratory Glassware and Chemicals required for analysis as per the system adopted.   

        Technical Details:

        • Reactor : Material Stainless Steel, Volume 2 Ltrs. (Approx.)
        • Water Bath : Material Stainless Steel, Double wall, insulated with Ceramic wool.
        • Heater : Nichrome wire Heater
        • Stirrer (2Nos.) : Stainless Steel Impeller and shaft coupled with FHP motor.
        • Temp. Sensor : RTD PT-100 type
        • Control panel comprises of :
        • Digital Temp. Controller : PID Controller, 0-199.9°C (For Water Bath) 

         

          Yes! I am Interested

          Computer Controlled Isothermal Batch Reactor

          REQUEST CALLBACK

          Computer Controlled Isothermal Batch Reactor
          Ask for Price

          Thanks for Contacting Us.

          Product Details:
          BrandAtico
          MaterialStainless Steel

          Computer Controlled Isothermal Batch Reactor (With Data Logging Facility)

          Description:

          A batch reactor is a closed system with no input and output streams. A batch reactor can operate under conditions like Isothermal (Temperature of Reaction Mass remains constant), Perfectly mixed (composition of reaction mixture is uniform throughout), and constant volume (volume of the reaction mixture within the reactor remains constant, there is no appreciable change in the density of reaction mass).. The temperature of bath can be maintained from ambient to 90°C with the help of Digital Temperature indicator Cum Controller. This setup is used to study a non-catalytic homogeneous reaction under isothermal condition. The set up consists of a Reactor fitted in a constant temperature water bath. One stirrer is fitted for mixing the reactants in reactor and other is fitted in water bath to keep the uniform temperature throughout in the bath

          Utilities Required:

          • Electricity Supply: Single Phase, 220 V AC, 50 Hz, 5-15 Amp combined socket with earth connection.
          • Earth voltage should be less than 5 volts.
          • Water Supply.
          • Floor Drain.
          • Instruments, Laboratory Glassware and Chemicals required for analysis as per the system adopted.
          • Computer System: i-3 processor with DVD Drive, Windows 7/8, MS-Office pre-loaded. One USB slot required in PC for Data Acquisition Card.   

          Technical Details:

          • Reactor : Material Stainless Steel, Volume 2 Ltrs. (Approx.)
          • Water Bath : Material Stainless Steel, Double wall, insulated with Ceramic Wool.
          • Heater : Nichrome wire Heater, with Control Unit to control heat input.
          • Agitator : Material Stainless Steel Impeller and shaft coupled with FHP motor
          • Stirrer : Stainless Steel Impeller and shaft coupled with FHP motor.
          • Product Analysis : By Electronic Sensor, Output 4-20 mA.
          • Temp. Measurement : By temperature transmitter (1No.), (0-200°C)
          • Control panel comprises of :
          • Digital Temp. Controller : PID Controller, 0-199.9°C, (For Water Bath)
          Yes! I am Interested

          Combined Flow Reactor

          REQUEST CALLBACK

          Combined Flow Reactor
          Ask for Price

          Thanks for Contacting Us.

          Product Details:
          BrandAtico
          MaterialStainless Steel

          Combined Flow Reactor (Compressed Air Feed System)

          Description:

          This set-up is used to study a non-catalytic homogeneous second order liquid phase reaction under ambient condition in a combined reactor. It consists of two reactors connected in series; one is plug flow reactor and another mixed flow reactor. In an ideal MFR (i.e. an ideal steady state flow reactor) the contents in reactor are well mixed and have uniform composition throughout. Thus the exit stream has the same composition as the fluid within the reactor. The compressed air is used for circulation of feed. 1st is a helical coil tube type reactor made up of SS pipe. Reactants enter at lower end coming out of the top of coil from where it is fed to a MFR fitted with stirrer for proper mixing. Samples are collected for analysis. Pressure Regulator, Pressure Gauge and Safety Valve are fitted in the compressed air line.

          Utilities Required:

          • Compressed Air Supply 0.5 CFM@1 bar
          • Water Supply
          • Floor Drain
          • Floor Area Required : 1.5 m x 0.75 m.
          • Instruments, Laboratory Glassware and Chemicals required for analysis as per the system adopted.  

          Technical Details:

          • 1st Reactor : Material Stainless Steel, Capacity (0.6-0.7) Ltrs. (approx.) (Helical Coiled Tube Type)
          • 2nd Reactor : Material Stainless Steel, Capacity 2 Ltrs (approx).
          • Stirrer for MFR : Stainless Steel Impeller and shaft coupled with FHP motor
          • Feed Tank (2Nos.) : Material Stainless Steel, Capacity 20 Ltrs.
          • Feed circulation : By compressed air.
          • Flow Measurement : Rotameter 2Nos. (One each for Reactants).
          • Piping : Stainless Steel and PU pipe
          • Pressure Regulator : 0-2 Kg/cm2
          • Pressure Gauge : Bourdon type 0-2 Kg/cm2
          Yes! I am Interested

          Isothermal Semi Batch Reactor

          REQUEST CALLBACK

          Isothermal Semi Batch Reactor
          Ask for Price

          Thanks for Contacting Us.

          Product Details:
          BrandATICO
          Capacity2 litre
          Material of ConstructionStainless Steel
          Max Pressure0-3 kg

          Isothermal Semi Batch Reactor (Compressed Air Feed System)

          Description:

          An isothermal semi-batch reactor is a semi-closed system with one input stream. It is operated under conditions like Isothermal (Temperature of Reaction Mass remains constant) and perfectly mixed (composition of reaction mixture is uniform throughout). Before starting the reaction the reactor is charged with measured quantity of one reactant. This set-up is used to study a noncatalytic homogeneous reaction under isothermal condition. The set up consists of a Reactor fitted in a constant temperature water bath. From a feed tank another reactant is fed to the reactor. Using a sampling pipette samples can be taken out for analysis after fixed interval. Rotameter is provided to measure the flow of Chemical.  

          Utilities Required:

          • Electricity Supply: Single Phase, 220 V AC, 50 Hz, 5-15 Amp combined socket with earth connection. Earth voltage should be less than 5 volts.
          • Compressed Air Supply: 0.5 CFM@1bar
          • Water Supply & drain.
          • Floor Area Required: 1 m x 0.75 m.
          • Instruments, Laboratory wares and Chemicals required for analysis as per the system adopted.   

          Technical Details:

          • Reactor : Material Stainless Steel, Capacity 2 Ltrs. (approx).
          • Water Bath : Material Stainless Steel, Double wall, insulated with Ceramic Wool.
          • Heater : Nichrome wire Heater
          • Stirrer : Material Stainless Steel Impeller and shaft coupled with FHP motor
          • Feed Tank (1Nos.) : Material Stainless Steel, Capacity 20 Ltrs.
          • Feed Circulation : By compressed air.
          • Flow Measurement : Rotameter.
          • Piping : Material Stainless Steel and PU pipe.
          • Pressure Regulator : 0-2 Kg/cm2
          • Pressure Gauge : Bourdon type 0-2 Kg/cm2
          • Temp. Sensor : RTD PT-100 type
          Yes! I am Interested

          Isothermal Semi-Batch Reactor

          REQUEST CALLBACK

          Isothermal Semi-Batch Reactor
          Ask for Price

          Thanks for Contacting Us.

          Product Details:
          BrandATICO
          Capacity2 litre
          MaterialStainless Steel
          Material of ConstructionStainless Steel
          Max Pressure0-3 kg
          Tank Capacity (Litre)20 Ltrs
          Volume (Litre)2 Ltrs

          Isothermal Semi-Batch Reactor (Compressed Air Feed System)

          Description:

          An isothermal semi-batch reactor is a semi-closed system with one input stream. It is operated under conditions like Isothermal (Temperature of Reaction Mass remains constant) and perfectly mixed (composition of reaction mixture is uniform throughout). This set-up is used to study a noncatalytic homogeneous reaction under isothermal condition.  

          Utilities Required:

          • Electricity Supply: Single Phase, 220 V AC, 50 Hz, 5-15 Amp combined socket with earth connection. Earth voltage should be less than 5 volts.
          • Compressed Air Supply: 0.5 CFM@1bar
          • Water Supply & drain.
          • Floor Area Required: 1 m x 0.75 m.
          • Instruments, Laboratory wares and Chemicals required for analysis as per the system adopted.   

          Technical Details:

          • Reactor : Material Stainless Steel, Capacity 2 Ltrs. (approx).
          • Water Bath : Material Stainless Steel, Double wall, insulated with Ceramic Wool.
          • Heater : Nichrome wire Heater
          • Stirrer : Material Stainless Steel Impeller and shaft coupled with FHP motor
          • Feed Tank (1Nos.) : Material Stainless Steel, Capacity 20 Ltrs.
          • Feed Circulation : By compressed air.
          • Flow Measurement : Rotameter.
          • Piping : Material Stainless Steel and PU pipe.
          • Pressure Regulator : 0-2 Kg/cm2
          • Pressure Gauge : Bourdon type 0-2 Kg/cm2
          • Temp. Sensor : RTD PT-100 type
          • Control panel comprises of :
          • Digital Temp. Controller : PID Controller, 0-199.9°C, For Water Bath
          Yes! I am Interested

          Combined Flow Reactor

          REQUEST CALLBACK

          Combined Flow Reactor
          Ask for Price

          Thanks for Contacting Us.

          Product Details:
          BrandATICO
          Capacity (0.6-0.7) Ltr
          MaterialStainless Steel
          Material of ConstructionStainless Steel
          Tank Capacity (Litre) 20 Ltrs
          Voltage (Volt) less than 5 volts
          Volume (Litre)(0.6-0.7) Ltr

          Combined Flow Reactor (Peristaltic Pump Feed System)

          Description:

          This set-up is used to study a non-catalytic homogeneous second order liquid phase reaction under ambient condition in a combined reactor. It consists of two reactors connected in series; one is plug flow reactor and another mixed flow reactor. In an ideal Plug Flow Reactor (PFTR) there is no mixing in the direction of flow and complete mixing perpendicular to direction of flow. The set up consists of two feed tanks through which two reactants are fed to the reactors fitted in series Peristaltic Pumps are provided to measure the individual flow of Chemicals. 1st is a helical coil tube type reactor made up of SS pipe. Reactants enter at lower end coming out of the top of coil from where it is fed to a MFR fitted with stirrer for proper mixing. Samples are collected for analysis. Concentration of reactants varies along the length of reactor but not in radial direction. In case of a coil turbulence is introduced due to frequent change in direction of flow and presence of secondary flow, so a higher value of reaction rate constant is expected in coil tube type plug flow reactor.

          Utilities Required:

          • Electricity supply: Single phase, 220 V AC, 50 Hz, 5-15 Amp combined socket with earth connection. Earth voltage should be less than 5 volts.
          • Water Supply & Drain
          • Instruments, Laboratory Glassware and Chemicals required for analysis as per the system adopted.  

          Technical Details:

          • 1st Reactor : Material Stainless Steel, Capacity (0.6-0.7) Ltr. (approx.) (Helical Coiled Tube Type)
          • 2nd Reactor : Material Stainless Steel, Capacity 2 Ltrs. (approx).
          • Stirrer for MFR : Stainless Steel Impeller and shaft coupled with FHP motor
          • Feed Tank (2Nos.) : Material Stainless Steel, Capacity 20 Ltrs.
          • Flow Measurement : Peristaltic Pumps- 2Nos. (One each for Reactants)
          • Piping : Stainless Steel and Silicon Pipe

           

          Yes! I am Interested

          Isothermal Semi Batch Reactor

          REQUEST CALLBACK

          Isothermal Semi Batch Reactor
          Ask for Price

          Thanks for Contacting Us.

          Product Details:
          Capacity2 litre
          MaterialStainless Steel
          Material of ConstructionStainless Steel
          Power (Kw)220 V AC, 50 Hz, 5-15 Amp
          Tank Capacity (Litre)20 Litre
          Voltage (V)less than 5 volt
          Volume (Litre)2 Ltr

          Isothermal Semi Batch Reactor (With Data Logging Facility)

          Description:

          one input stream. It is operated under conditions like Isothermal (Temperature of Reaction Mass remains constant) and perfectly mixed (composition of reaction mixture is uniform throughout). This set-up is used to study a non-catalytic homogeneous reaction under isothermal condition. The set up consists of a Reactor fitted in a constant temperature water bath. Before starting the reaction the reactor is charged with measured quantity of one reactant. From a feed tank another reactant is fed to the reactor. Peristaltic Pump is provided to measure the flow of Chemical. One stirrer is fitted for mixing the reactants in reactor and other is fitted in water bath to keep the uniform temperature throughout in the bath. The temperature of bath can be maintained from ambient to 70°C with the help of Digital Temperature indicator Cum Controller..

          Utilities Required:

          • Electricity Supply: Single Phase, 220 V AC, 50 Hz, 5-15 Amp combined socket with earth connection. Earth voltage should be less than 5 volts.
          • Water Supply & Drain
          • Instruments, Laboratory wares and Chemicals required for analysis as per the system adopted.
          • Computer System: i3 processor with DVD Drive, Windows 7/8, MS-Office pre-loaded. One USB slot required in PC for Data Acquisition Card

          Technical Details:

          • Reactor : Material Stainless Steel, Capacity 2 Ltrs. (approx).
          • Water Bath : Material Stainless Steel, Double wall, insulated with Ceramic Wool.
          • Heater : Nichrome wire Heater
          • Stirrer : Material Stainless Steel Impeller and shaft coupled with FHP motor
          • Feed Tank (1Nos.) : Material Stainless Steel, Capacity - 20 Ltrs.
          • Flow Measurement : Peristaltic Pump- 1Nos.
          • Product Analysis : By using Electronic Sensor, Output 4-20 mA.
          • Piping : Material Stainless Steel and Silicon pipe.
          • Temp. Measurement : Temperature transmitter-1No. RTD PT-100 type
          • Control panel comprises of :
          • Digital Temp. Controller : PID Controller 0-199.9°C (For Water Bath)
          Yes! I am Interested

          Isothermal Semi Batch Reactor

          REQUEST CALLBACK

          Isothermal Semi Batch Reactor
          Ask for Price

          Thanks for Contacting Us.

          Product Details:
          BrandAtico
          MaterialStainless Steel

          Isothermal Semi Batch Reactor (Peristaltic Pump Feed System)

          Description:

          An isothermal semi-batch reactor is a semi-closed system with one input stream. It is operated under conditions like Isothermal (Temperature of Reaction Mass remains constant) and perfectly mixed (composition of reaction mixture is uniform throughout). This set-up is used to study a noncatalytic homogeneous reaction under isothermal condition.  

          Utilities Required:

          • Electricity Supply: Single Phase, 220 V AC, 50 Hz, 5-15 Amp combined socket with earth connection. Earth voltage should be less than 5 volts.
          • Water supply and drain.
          • Instruments, Laboratory wares and Chemicals required for analysis as per the system adopted.   

          Technical Details:

          • Reactor : Material Stainless Steel, Capacity 3.0 Ltrs. (approx).
          • Water Bath : Material Stainless Steel, Double wall, insulated with Ceramic wool.
          • Heater : Nichrome wire Heater
          • Stirrer : Material Stainless Steel Impeller and shaft coupled with FHP motor
          • Feed Tank (1Nos.) : Material Stainless Steel, Capacity 20 Ltrs.
          • Flow Measurement : Peristaltic Pumps, 2Nos. (One each for reactants).
          • Piping : Material Stainless Steel and Silicon Pipe.
          • Temp. Sensor : RTD PT-100 type
          Yes! I am Interested

           
          X


          Contact via E-mail
          Contact via SMS
          Advanced Technocracy Inc.
          Kunal Chopra (CEO)
          Atico House 5309, Grain Market Near B.D School,
          Ambala - 133001, Haryana, Atico House 5309, Grain Market,
          Call Us: 
          Call Response Rate: 72%
          Share Us :
          F G T L



          Home  |   Profile   |  Our Products  |  Site Map  |   Contact Us   |   Mobile Site

          © Advanced Technocracy Inc.. All Rights Reserved (Terms of Use)
          Developed and Managed by IndiaMART InterMESH Limited

          Advanced Technocracy Inc.