Microprocessor and Microcontroller Lab

Low Cost 8085 Microprocessor Trainer Kit With Inbuilt Power Supply

• Based on 8085 CPU operating at 6.144 MHz crystal frequency 
• Based on 8085 CPU operating at 6.144 MHz crystal frequency 
• 8K bytes of RAM available to the user 
• 16 bit programmable TIMER/COUNTER using 8253. 
• 24 programmable I/O lines provided through 8255. 
• RS-232C interface through SID/SOD Lines with Auto baud rate. 
• Two modes of commands: - Hex Key pad mode - Serial mode All address, data & control lines are buffered and made available at the edge connector as per STD bus configuration. 
• 25/28 key hexadecimal keyboard and six seven segment displays through 8279. 
• Powerful software commands like Relocate, String, Fill, Insert, Delete, Block Move, Examine/Compare Memory, Examine Register, Insert Data, Delete Data, Single Step, GO, Break Point in both Serial & Keyboard mode. 
• Facility for Downloading/Uploading files from/to PC. 
• In-built Power supply 
• User's Manual. 

8085 Microprocessor Training Kit With Inbuilt Power Supply

• Based on 8085 CPU operating at 6.144 MHz crystal frequency 
• 8K bytes of EPROM loaded with powerful monitor program 
• Total on board memory expansion upto 64K bytes using 2732/2764/27128/6264/ 62256 with 1 socket of 28 pin. 
• Battery back up for RAM with 3.6V rechangeable cell. 
• Memory mapping definable by the user. 
• 16 bit programmable TIMER/COUNTER using 8253. 
• 24 I/O lines provided through 8255 
• 22 I/O lines provided through 8155 
• RS-232C interface through SID/SOD Lines withAuto baud rate. 
• Two modes of commands: - Hex Key pad mode & - Serial mode All address, data & control lines are buffered and made available at the edge connector as per STD bus configuration. 
• 25/28 key hexadecimal keyboard and six seven segment displays through 8279 
• Powerful software commands like Relocate, String, Fill, Insert, Delete, Block Move, Examine/Compare Memory, Examine Register, Insert Data, Delete Data, Single Step, GO, Break Point in both Serial & Keyboard mode. 
• Facility for Downloading/Uploading files from/to PC. 
• In-Built power supply:+5V/1.2A 
• User's Manual. 

8085 Microprocessor Trainer Kit With Lcd Display And Inbuilt Power Supply

• Based on 8085 CPU operating at 6.144 MHz crystal frequency. 
• 8K bytes of EPROM loaded with powerful monitor program. 
• 8/32K bytes of RAM available to the user 
• Battery back up provided for RAM area. 
• Battery back up provided for RAM area. 
• Memory mapping definable by the user. 
• 16 bit programmable TIMER/COUNTER using 8253. 
• 24 programmable I/O lines provided through 8255. 
• RS-232C interface through SID/SOD Lines with Auto baud rate. 
• All address, data & control lines are buffered and made available at the edge connector as per STD bus configuration. 
• 104/105 Keys IBM PC Compatible ASCII keyboard 
• 16x1 LCD display with backlite. 
• Powerful software commands like Relocate, String, Fill, Insert, Delete, Block Move, Examine/Compare Memory, Examine Register, Insert Data, Delete Data, Single Step, GO, Break Point in both Serial & Keyboard mode. 
• Facility for Downloading/Uploading files from/to PC. 
• On board Assembler/Disassembler. 
• Facility of writing program in assembly language 
• In-Built Power Supply 
• User's Manual. 

8085 Microprocessor Training Kit With Lcd Display Adc, Dac & Inbuilt Power Supply

• Based on 8085 CPU operating at 6.144 MHz crystal frequency.
• 8K bytes of EPROM loaded with powerful monitor program.
• 8K bytes of RAM available to the user
• Total on board memory expansion upto 64K bytes.
• Memory mapping definable by the user.
• 16 bit programmable TIMER/COUNTER using 8253.
• 48 programmable I/O lines provided through 8255.
• RS-232C interface through SID/SOD Lines with Auto baud rate.
• USB Interface to connect kit to computer (Optional)
• Two modes of commands: - Hex Key pad mode - Serial mode All address, data & control lines are buffered and made available at the edge connector as per STD bus configuration.
• 104/105 keys IBM PC compatible ASCII keyboard
• LCD display with backlite
• Powerful software commands like Relocate, String, Fill, Insert, Delete, Block Move, Examine/Compare Memory, Examine Register, Insert Data, Delete Data, Single Step, GO, Break Point in both Serial and Keyboard mode.
• I/O Lines Controlled
• 8 LED using 8 Nos. of I/O Lines
• 2 relay of 12V & 1 Opto
• 8 bit DAC using DAC-0800.
• 8 Channel 8 bit ADC using ADC-0809.
• Facility for Downloading/Uploading files from/to PC.
• On board Disassembler.

8085 Microprocessor Training Kit With Eprom Programmer & In-built Power Supply

• Based on 8085 CPU operating at 6.144 MHz crystal frequency. 
• 8/16K bytes of EPROM loaded with powerful monitor program. 
• 8/16K bytes of RAM available to user. 
• Battery Backup for RAM with 3.6V rechargeable cell. 
• Total on board memory expansion upto 64K bytes using 2732/2764/27128/6264/ 62256 with total 4 sockets of 28 pin. 
• Memory mapping definablebythe user. 
• 16 bit programmable TIMER/COUNTER using 8253 
• 48 programmable I/O lines provided through 2 nos.of 8255 
• RS-232C interface for CRT Terminal with auto baud rate. 
• EPROM Programmer for 27 series using 28 pin ZIF socket with facility to Program, Verify, List & Blank Check. 
• Two modes of commands: Hex Key pad mode & Serial mode 
• All address, data & control lines are buffered and made available at the edge connector as per STD bus configuration. 
• 25/28 key hexadecimal keyboard and six seven segment display through 8279. 
• Powerful software commands like Relocate, String, Fill, Insert, Delete, Block Move, Examine & Compare Memory, Examine Register, Insert Data, Delete Data, Single Step, GO, Break Point in both Serial and Keyboard mode. 
• On Line Single Line Assembler/Disassembler. 
• Facility for Downloading/Uploading files from/to PC. 
• In-built Power supply 
• User's Manual. 

8085 Advanced Microprocessor Trainer Kit With With Onboard A To D, D To A, Eprom Programmer & Inbuil

• Based on 8085 CPU operating at 6.144 MHz crystal. 
• 16K bytes of EPROM loaded with powerful monitor program. 
• 8K byte of RAM available to the user. 
• Total on board memory expansion upto 64K bytes using 2732/2764/27128/6264. 
• Memory mapping definable by the user. 
• Six seven segment Hexadecimal display 
• 48 programmable I/O lines using two nos. of 8255. 
• 16 bit programmable timer/counter using 8253. 
• Additional serial port using 8251. 
• EPROM Programmer for 27 series EPROM's with 28 pinZIF. 
• Printer inteface (optional) 
• Battery backup for RAM using 3.6V rechargeable cell. 
• RS-232C interface for CRT using SID/SOD lines. 
• Interrupt Controller using 8259. 
• Onboard 1 Channel 8 bit D/A using DAC 0800. 
• Onboard 1 Relay output. 
• Onboard 1 Opto isolated input 
• 25/28 Computer graded keys hexadecimal keys 
• Two modes of Commands: - Hex Key Pad Mode - Serial Mode All address, data and control lines are buffered and made available at the edge connector as per STD Bus configuration. 
• All address, data and control lines are buffered and made available at the edge connector as per STD Bus configuration

8085 Microprocessor Training Kit With Lcd Display And In-built Power Supply

• Based on 8085 CPU operating at 6.144 MHz crystal. 
• 16K bytes of EPROM with powerful monitor program. 
• 8K byte of RAM available to the user. 
• Battery backup for user's RAM with 3.6V rechargeable cell 
• Total on board memory expansion upto 64K bytes using 2732/2764/27128/6264. 
• Memory mapping definable by the user. 
• 20x2 Liquid Crystal Display (LCD). 
• 104/105KeysIBM PC Compatible ASCII Keyboard 
• 48 programmable I/O lines provided through 2 nos. of 8255. 
• 16 bit programmable timer/counter using 8253. 
• RS-232C interface for CRT using SID / SOD lines. 
• Two modes of Commands: - Key board Mode & Serial Mode 
• All address, data and control lines are buffered and made available at the edge connector as per STD Bus configuration. 
• Powerful Software Commands like relocate, string, fill, insert, delete, block move, memory compare etc. 
• Onboard Single Line Assembler/Disassembler. 
• Facility for Downloading/Uploading files from/to PC. 
• In-built Power Supply : 
• User's Manual. 

8085 Advanced Microprocessor Training Kit With Lcd Display, Adc, Dac, Eprom Programmer And & In-built

• Based on 8085 CPU operating at 6.144 MHz crystal. 
• 16K bytes of EPROM with powerful monitor program. 
• 8K byte of RAM available to the user. 
• Battery backup for user's RAM with 3.6V rechargeable cell 
• Total on board memory expansion upto 64K bytes using 2732/2764/27128/6264. 
• Memory mapping definable by the user. 
• 20x2 Liquid Crystal Display (LCD). 
• 104/105KeysIBM PC Compatible ASCII Keyboard 
• 48 programmable I/O lines provided through 2 nos. of 8255. 
• 16 bit programmable timer/counter using 8253. 
• Additional serial port using 8251. 
• EPROM Programmer for 27 series with 28 pin ZIF. 
• Printer Inteface. 
• RS-232C interface for CRT using SID / SOD lines. 
• Interrupt Controller using 8259. 
• 8 Channel 8 bit ADC using 0809. 
• 1 Channel 8 bit D/A using DAC 0800. 
• 1 Relay output. 
• 1 Opto isolated input. 
• Two modes of Commands: - Key board Mode & Serial Mode All address, data and control lines are buffered and made available at the edge connector as per STD Bus configuration.

8085 Microprocessor Training Kit Cum Emulator With In-built Power Supply

• Based on 8085 microprocessor operating at 6.144Mhz clock frequency. 
• VMC-ICE8085P comprises of three components viz., a) Microprocessor Kit b) In-circuit Emulator c) Cross Assembler 48K Emulation Memory, RAM area starting from 0000H. 
• 48K Emulation Memory, RAM area starting from 0000H. 
• Onboard battery backup for 8K emulation memory. 
• 8K byte of EPROM loaded with powerful monitor program. 
• 48 I/O lines using 2 nos. of 8255 
• 16 bit timer/counter using 8253. 
• 28 Keys Hexadecimal Keyboard and six digit seven segment display. 
• 40 pin Header with cable for connecting the target system. 
• Programmer for 27 series EPROMs with facility to Blank Check, Verify, Program & Read 
• Can be operated in both Serial & Stand-alone mode. 
• RS232 port for serial communication with IBM-PC/XT/AT. 
• Powerful Software commands like Break-point, Single Stepping, Auto Single Stepping, Go, Fill, Display, Compare, Origin, Memory, Zoom, Select, Com. 
• Uploading & Downloading of files from/to PC. 
• Onboard disassembler. 
• In-built Power Supply : 
• User's Manual. 

8086  8088 Microprocessor Trainer kit with inbuilt power supply

• Based on intel's 8086/8088 cpu operating at 2. 5/5mhz 
• 16k bytes of ram available to the user using 6264 
• 16k bytes of eprom loaded with powerful monitor program(2764/27128).  
• total on board memory capacity of 128kb of ram & 128kb of eprom.  
• battery backup provided for ram area.  
• 48 i/o lines through 2 nos. Of 8255.  
• 16 bit timer/counter through 8253.  
• rs-232c for crt terminal through 8251 baud rate selection through dip switch from 110-19,200 baud.  
• 25/28 keys hexadecimal keyboard and eight seven segment display.  
• resident monitor with two modes of operation: - keyboard mode & serial mode powerful software commands like go, examine/modify registers, single stepping, block move, fill, insert, delete, input/output byte & word.  
• facility for uploading/downloading of files from/to pc.  
• all address, data and control signals, are buffered and available at the frc connector.  
• in-built power supply.  
• user's manual.  

8086   8088 Microprocessor Training Kit With Eprom Programmer & Inbuilt Power Supply

Based on Intel's 8086/8088 CPU operating at 2.5/5MHz. 
16K bytes of RAM available to the user using 6264 
16K bytes of EPROM loaded with powerful monitor program(2764/27128). 
Total on board memory capacity of 128KB of RAM & 128KB of EPROM. 
Battery backup provided for RAM area. 
48 I/O lines through 2 nos. of 8255. 
16 bit Timer/Counter through 8253. 
RS-232C for CRT Terminal through 8251 Baud rate selection through DIP switch from 110-19,200 baud. 
EPROM Programmer for 2732/2764/27256 with 28 pin ZIF with facility to Program, Verify, List & Blank Check for Even, Odd & Continuous bytes. 
25/28 keys hexadecimal keyboard and eight seven segment display. 
Resident Monitor with two modes of operation: - Keyboard mode & Serial mode Powerful software commands like GO, EXAMINE/MODIFY REGISTERS, SINGLE STEPPING, BLOCK MOVE, FILL, INSERT, DELETE, INPUT/OUTPUT BYTE & WORD. 
Facility for uploading/downloading of files from/to PC. 
All Address, Data and Control Signals, are buffered and available at the FRC connector. 
In-built Power Supply. 
User's Manual. 

8086  8088 Microprocessor Training Kit With Adc, Dac And In-built Power Supply

Based on Intel's 8086/8088 CPU operating at 2.5/5MHz. 
16K bytes of RAM available to the user using 6264 
16K bytes of EPROM loaded with powerful monitor Program (2764/27128). 
Total on board memory capacity of 128K bytes of RAM and 128 K bytes of EPROM. 
Battery backup provided for RAM area. 
48/72 I/O lines through 8255. 
16 bit Timer/Counter through 8253. 
RS-232C for CRT Terminal through 8251 Baud rate selection through DIP switch from 110-19,200 baud. 
Analog to Digital converter 
25/28 keys hexadecimal keyboard and eight seven segment display. 
Resident Monitor with two modes of operation: - Keyboard mode & Serial mode Powerful software commands like GO, EXAMINE/MODIFY REGISTERS, SINGLE STEPPING, BLOCK MOVE, FILL, INSERT, DELETE, INPUT/OUTPUT BYTE & WORD. 
Facility for uploading/downloading of files from/to PC. 
All Address, Data and Control Signals, are buffered and available at the FRC connector. 
In-built Power Supply : 
User's Manual. 

ADC INTERFACE CARD 

Uses 8 bit ADC-0809 monolithic C-MOS device with in-built 8 channel multiplexer. 
Eight LED's are provided to display the digital value of the input Analog Signal 
.The complete operation of A/D converter Chip can be understood using this card. 

DAC Interface Card

Consists of two independent 8 bit Digital to Analog Converter analog with a stable regulated voltage source using 723 regulator. 
The current outputs of the DAC are converted to voltages using operational amplifiers. 

IC Tester Interface Card

The interface tests 14 pin or 16 pin digital IC's. 
Three personality modules are to be inserted in three different sockets for the IC under test. 
A socket is provided for inserting the IC to be tested.

8086 Microprocessor Training Kit With LCD Display A/d, D/a & In-built Power Supply

Based on Intel's 8086/8088 CPU operating at 2.5/5MHz. 
32K bytes of RAM available to the user 
32K bytes of EPROM loaded with powerful monitor program(2764/27128). 
Total on board memory capacity of 256K bytes of RAM and 256 K bytes of EPROM. 
Battery backup provided for RAM area. 
72 I/O lines through three nos. of 8255. 
16 bit Timer/Counter through 8253. 
RS-232C for CRT Terminal through 8251 Baud rate selection through DIP switch from 110-19,200 baud. 
Real Time Clock (optional) 
20x2 Liquid Crystal Display. 
Parallel Printer interface with disassembler listing 
Analog to Digital converter 
Digital to Analog converter 
Supports MASM (Macro Assembler) 
Resident Monitor with two modes of operation: - Keyboard mode & Serial mode Resident Monitor with two modes of operation: - Keyboard mode & Serial mode 
Powerful software commands like GO, EXAMINE/MODIFY REGISTERS, SINGLE STEPPING, BLOCK MOVE, FILL, INSERT, DELETE, INPUT/OUTPUT BYTE & WORD. 
Facility for uploading/downloading of files from/to PC. 
All Address, Data and Control Signals, are buffered and available at the FRC connector. 
In-built Power Supply 
User's Manual.

8031 Microcontroller Training Kit With Inbuilt Power Supply

Based on 8031/8051/8751 operating at 10/12 MHz. 
On board 8K RAM. 
Battery backup for RAM area. 
8/16K bytes of EPROM with powerful monitor program. 
Total memory expandable upto 128K Bytes using four 28 pin sockets. 
48 I/O lines using 2 nos. of 8255. 
Two External interrupts INT0 & INT1. 
28 keys Hexadecimal Keyboard and six Seven Segment displays. 
RS-232C interface using 8251. 
Auxiliary RS-232C using serial pins of 80C31. 
All data, address and control signals (TTL compatible) available at FRC connector. 
Powerful software commands like INSERT, DELETE, BLOCK MOVE, SET/CLEAR BREAK POINT, SINGLE STEP, EXAMINE THROUGH REGISTER, EXECUTE, EXAMINE, MODIFY, PROGRAM/DATA/INTERNAL MEMORY etc. 
Uploading/Downloading facility from PC in Intel Hex format. 
In-built Power Supply User's Manual. 
User's Manual. 

8086 8088 Microprocessor Training Kit With Lcd Display & In-built Power Supply

Based on 8086/8088 Microprocessor 
Onboard assembler & disassembler. 
Onboard assembler & disassembler. 
16K bytes of CMOS RAM expandable to 128K Bytes using 6264/62256. 
72 I/O lines using three nos. of 8255. 
8 different level interrupt through 8259. 
Three 16 bit Timer/Counter through 8253. 
104/105Keys IBM PC Compatible ASCII Keyboard 
20x2 Liquid Crystal Display. 
RS-232C Port using 8251. 
All address, data and control signals (TTL Compatible) available at edge connector as per Multi Bus. The kit also has its own Resident Bus. 
In-built Power Supply 
User's Manual. 

8051 Micro Controller training kit with lcd display & in-built power supply

Based on 8051/89c52 micro controller
on board 32k ram.  
Battery backup for ram area 
64 k bytes of eprom with powerful monitor program 
48 i/o lines using 2 nos. Of 8255 
3 channel programmable timer/counter using 8253 
two external interrupts int0 & int1 from cpu 
20 x 2 lcd (liquid crystal display) is provided for display 
ibm pc compatible keyboard for entering the program, editing and executing the programs.  
rs-232c interface using 8251 
one serial usart interface provided by 89c51/89c52 
all data, address and control signals (ttl compatible) available at frc connector 
powerful software commands like insert, delete, block move, set/clear break point, single step, examine register, execute, examine/modify memory etc.  
in-built power supply 
detailed user's manual.  

8051 Advanced Microcontroller Training Kit With Lcd Display, Ad/da & Inbuilt Power Supply

Based on 8051/89C52 microcontroller 
On board 32K RAM. 
Battery backup for RAM area 
64 K bytes of EPROM with powerful monitor program 
48 I/O lines using 2 Nos. of 8255 
3 channel programmable timer/counter using 8253 
Two external interrupts INT0 & INT1 from CPU 
IBM PC compatible keyboard for entering the program, editing and executing the programs. 
20 x 2 LCD (Liquid Crystal Display) is provided for display 
RS-232C interface using 8251 
One serial USART interface provided by 89C51/89C52 
All data, address and control signals (TTL compatible) available at FRC connector 
Powerful software commands like INSERT, DELETE, BLOCK MOVE, SET/CLEAR BREAK POINT, SINGLE STEP, EXAMINE REGISTER, EXECUTE, EXAMINE/MODIFY MEMORY etc. 
On board Analog to Digital converter using ADC0809 
On board Digital to Analog converter using DAC 0800 
Real Time Clock (optional) 
In-built Power Supply. 
Detailed User's Manual.0 

8051 Microcontroller Training Kit Cum Emulator With In-built Power Supply

Based on 8031/8051 microcontroller operating at 10/12Mhz clock frequency 
VMC-ICE 31/51P comprises of four components viz., a) Microcontroller Kit b) In-circuit Emulator c) MBUG Symbolic Debugger d) MBUG Cross Assembler 
8K Emulation Memory expandable upto 48K. 
Onboard battery backup for 8K emulation memory 
8K byte of EPROM loaded with powerful monitor program 
48 I/O lines using 2 nos. of 8255. 
16 bit timer/counter using 8253. 
32 keys keyboard and Six Digit Seven Segment display. 
8 LEDs for displaying contents of registers and two LEDs for current emulation memory 
8 channel 8 bit A/D Converter using ADC 0809. 
Single channel D/A Converter using DAC 0800. 
40 pin Header with cable for connecting the target system. 
RS232 port for serial communication with IBM-PC/XT/AT. 
Powerful Software commands like Break- point, Single Stepping, Trace, Go, Print, Fill, Display, Compare, Scalar, Auto, Match, Non-match, Origin, Memory Zoom, Select Emulate, Com 
Uploading & Downloading of files from/to PC. 
Onboard assembler/disassembler. 
In-built Power Supply 
User's Manual. 

8051 Advanced Microcontroller Training Kit With Lcd Display, Ad/da & Inbuilt Power Supply

Based on 8051/89C52 microcontroller 
On board 32K RAM. 
Battery backup for RAM area 
64 K bytes of EPROM with powerful monitor program 
48 I/O lines using 2 Nos. of 8255 
3 channel programmable timer/counter using 8253 
Two external interrupts INT0 & INT1 from CPU 
IBM PC compatible keyboard for entering the program, editing and executing the programs. 
20 x 2 LCD (Liquid Crystal Display) is provided for display 
RS-232C interface using 8251 
One serial USART interface provided by 89C51/89C52 
All data, address and control signals (TTL compatible) available at FRC connector 
Powerful software commands like INSERT, DELETE, BLOCK MOVE, SET/CLEAR BREAK POINT, SINGLE STEP, EXAMINE REGISTER, EXECUTE, EXAMINE/MODIFY MEMORY etc. 
On board Analog to Digital converter using ADC0809 
On board Digital to Analog converter using DAC 0800 
Real Time Clock (optional) 
In-built Power Supply. 
Detailed User's Manual.0

8051 Microcontroller Training Kit Cum Emulator With In-built Power Supply

Based on 8031/8051 microcontroller operating at 10/12Mhz clock frequency 
VMC-ICE 31/51P comprises of four components viz., a) Microcontroller Kit b) In-circuit Emulator c) MBUG Symbolic Debugger d) MBUG Cross Assembler 
8K Emulation Memory expandable upto 48K. 
Onboard battery backup for 8K emulation memory 
8K byte of EPROM loaded with powerful monitor program 
48 I/O lines using 2 nos. of 8255. 
16 bit timer/counter using 8253. 
32 keys keyboard and Six Digit Seven Segment display. 
8 LEDs for displaying contents of registers and two LEDs for current emulation memory 
8 channel 8 bit A/D Converter using ADC 0809. 
Single channel D/A Converter using DAC 0800. 
40 pin Header with cable for connecting the target system. 
RS232 port for serial communication with IBM-PC/XT/AT. 
Powerful Software commands like Break- point, Single Stepping, Trace, Go, Print, Fill, Display, Compare, Scalar, Auto, Match, Non-match, Origin, Memory Zoom, Select Emulate, Com 
Uploading & Downloading of files from/to PC. 
Onboard assembler/disassembler. 
In-built Power Supply 
User's Manual.

Msc Training Board For Vmc-ice 31/51p In Circuit Emulator (project Board)

Stepper Motor: control of stepper motor in all parameters such as direction, speed and no. of steps. 
ADC: 8 bit Analog to Digital Conversion using successive approximation technique for A to D conversion. 
Speaker: how to generate the beep through I/O port.Dot Matrix FND. 
Working of sliding switches. 
Working of push buttons. 
Working of LED. 
User's Manual, Cables & Connectors. 

Logic Controller Interface Card

The logic controller interface provides the user with eight TTL buffered outputs and eight TTL buffered inputs. 
The logic state of each input and output is indicated by LED's. 
This module can be effectively used to teach 8255 input & output modes 
. It can also simulate Ladder networks. 

Display Interface Card

A four digit seven segment display using shift registers can be obtained on corresponding to be put out in serial fashion to the input of the first shift register and clock terminal is pulsed. 
Has the capability of displaying any segment combination.

Stepper Motor Controller Interface Card With Stepper Motor And Power Supply

Can control Stepper Motor in three parameters such as direction, speed and number of steps. 
It has got driver transistor for driving all the phases of the motor useful for Robotic and incremental control applications. 

Keyboard interface card 

A calculator style kb consisting of the keys 0 to 9, *, +, -, /, c ce and two user definable keys, allowing the user to study a number of techniques used in key board interfacing like software debouncing, two key lockout and keyboard encoding and pausing.

Two In One Microcontroller Training Kit With With In-built Power Supply

CPU Based on 8097BH/80C196KC/80C196KB 
16K bytes of RAM expandable to 32K with 3.6V rechargeable Battery Backup 
16K bytes of EPROM expandable to 32K loaded with powerful monitor 
Onboard Assembler/Disassembler. 
24 Parallel I/O lines using 8255 and 8 buffered lines from 8097. 
1 input port software programmable to be 8 bit digital input port or 8 analog channels with 10 bit A/D Converter and sample & hold with a 24 µsec. (for 12MHz Crystal) conversion time using successive approximation for conversion 
RTC & Watch-Dog Timer 
High speed I/O (HSIO) port with 8 lines. Four lines dedicated as output, two lines dedicated as input, and two either as input or output. 
Serial port from the controller. 
Two 16 bit timers (one with external clock input). 
Cross Assembler for 8097/80196. 
28 Keys Keyboard & 8 Seven Segment displays. 
Facility of Uploading/Downloading files to/from PC. 
Software for Modify/Display Register, Modify/Display Memory, Execution of Program, Break-point, Single Stepping etc. 
EPROM Programmer for 2764/27128/27256 with facility to program, List, Verify and Blank Check for continuous, odd or even bytes. 
In-built Power Supply. 
User's Manual. 

Elevator Simulator Interface Card

This interface simulates the control operation of an elevator. 
The elevator is considered to function within a building having four floors 
A key and corresponding LED indicator serves as a request button and request status indicator. 
The LED's also indicate the position of the elevator within the shaft 
This module is the practical example of use of Microprocessor in industry. 

LCD Display Interface Card

A 16x1 Liquid Crystal Display using shift registers can be obtained on corresponding to be put out in serial fashion to the input of the first shift register and clock terminal is pulsed. 
It has the capability of displaying any segment combination. 

Traffic Light Controller Interface Card

The Traffic Light Controller Card has RED, AMBER & GREEN LED's to demonstrate the use of Microprocessor in controlling the traffic movement under the control of program. 
It is a good example of use of Microprocessor in common applications. 

Temperature Measurement Interface Card With Thermocouple

Sensor to measure temperature upto 150 deg. C. Along with room temperature compensation 
and amplifier with output of 0-5V corresponding to the temperature.

DC Motor Controller Interface Card With Motor And Power Supply

The VMC-DC card can control the speed of DC motor along with its direction under the control of the software programme. 

Relay & Opto Coupler Interface Card

The VMC-ROC has four channel relay & opto coupler to demonstrate how I/O lines can be used to energise the relay and opto coupler to sense the input providing isolation. 

LED Display Matrix Interface Card

The VMC-LED has a matrix of 8 x 8 LED's and is a module to demonstrate for displaying any character within the matrix. 

Thumb Wheel Switch Interface Card

The VMC-TWSC has two nos. of Thumb Wheel Switches which can be read through I/O lines normally used in industrial controllers. 

12 Bit ADC Interface Interface Card

This interface consists of 8 channel 12 bit AD574 device with 15 microseconds conversion timer. 
Both unipolar and bipolar operations are possible.
This modules can be used where 12 bit conversion is required for better accuracy and resolution of ADC.

ADC & DAC Interface Card

Uses 8 bit ADC & 8 bit DAC. LED's are provided to display the digital value of the input Analog Signal. 
The current outputs of the DAC are converted to voltages using operational amplifiers. 

Printer Interface Card

This interface card s uses 8255 of the Microprocessor / Microcontroller to print output of the printer.