Soil Test Instruments

Advanced Technocracy Inc. is Manufacturer, Exporter & Supplier of Soil Drying Ovens

Technical Description

 

For trimming various diameter specimen for triaxial and unconfined compression tests.
specification:the lower specimen grip is mounted on a disc which rotates freely. The soil sample is mounted on the lower specimen grip and the upper grip is firmly seated on top of the specimen. The vertical guide can be adjusted to control the depth of cut. While trimming the lower disc is rotated by hand. Supplied complete with a wire saw. Trimming knife, mounted on a support, can be adjusted horizontally as well as vertically to permit trimming of the specimen to the exact size of the ring. A guide supplied prevents over cutting. Complete with 38mm, 50mm, 75mm and 100mm dia specimen rings.  

Unconfined Compression Tester Proving Ring Type (Hand Operated)

This is a hand operated instrument for determining the unconfined compression strength of soil specimens of diameter ranging from 38mm to 100mm. Load on the sample is applied gradually by a hand operated load frame and loads are measured on a sensitive proving ring attached to the load frame.

Specification

• Comprises of a hand operated load frame
• cap. 5000 kgf with screw jack for loading
• handle and strain dial gauge bracket
• adapter for proving ring, conical seats and male / female coning tools for 38mm dia samples
• Supplied without proving ring, dial gauge.

This is similar to with the added advantage of a motorized drive permitting a choice of three constant rates of stain.

Specification:

• Comprises a screw operated load frame
• cap.5000kg with a gear box and motor drive giving 1.25, 1.5, 2.5mm/min
• Rates of strain, a pair of cone seating, adapter for proving ring, and stain dial gauge bracket. Supplied with one pair of male/female coning tools for 38mm dia samples but without ring and dial gauge Suitable for operation on 230 V
• Single Phase A.C. Supply.

Accessories:

• Coning tools in pairs (Male & Female) for samples having diameter 38mm, 50mm, 75mm & 100mm.

This is similar to with the added advantage of a motorized drive permitting a choice of three constant rates of stain.


Specification:

• Comprises a screw operated load frame
• cap.5000kg with a gear box and motor drive giving 1.25, 1.5, 2.5mm/min
• Rates of strain
• a pair of cone seating
• adapter for proving ring
• stain dial gauge bracket
• Supplied with one pair of male/female coning tools for 38mm dia samples but without ring and dial gauge
• Suitable for operation on 230 V, Single Phase A.C. Supply.

Accessories:

• Coning tools in pairs (Male & Female) for samples having diameter 38mm, 50mm, 75mm & 100mm.

The unconfined compression test apparatus for soil includes uniaxial compression test in which the test specimen is provided with no lateral support while undergoing vertical compression. The test measures the unconfined compression strength of a cylinder of cohesive or semi cohesive soil and indirectly shearing strength. The shearing strength of the soil is generally taken to be one half of the unconfined compression strength. The unconfined compression test apparatus is used normally on a undisturbed sample with its natural moisture content. It may also be performed on remolded samples to evaluate the consequences of disturbances and remolding. 
Unconfined Compression Test Apparatus is normally useful in soil mechanics laboratories. The unconfined compression test is the simplest and quickest method for evaluation of the shear strength of cohesive soil in the laboratory or in the field. The results from compression test apparatus are widely used in ascertaining the relative consistency and sensitivity for estimating the ultimate bearing capacity.

The apparatus consists of following:

• Load Frame 50kN capacity
• Electrically cum Manually Operated with 3 rates of strains 1.25mm, 1.50mm, 2.50mm/min
• 1No.Split Mould 38mm dia
• 1No.Set of Conning Tools
• 1 Set of Conning Plates with Springs
• 1 Set Proving Ring, 2.5kN capacity fitted with dial gauge with set of loading pads and calibration certificate by NCCBM (Govt Testing Lab) in a nice wooden carrying case
• Dial gauge 0.01mm x 25mm travel The Machine is fitted with ¼ HP Motor
• Suitable for Operation on 220V, Single Phase, 50Hz, AC Supply.

Load Frames are used to apply load on the test specimen. The capacity and speed depends on the requirement of a particular test. Load Frames are used in C.B.R. Triaxial, Unconfined Compression Test etc.

Spring type unconfined compression testing apparatus (Spring Type Autographic) can be used either in a laboratory or in field.


Specification :

• Consists of a spring operated load frame with arrangements for loading 38mm x 76mm samples
• one set of four load springs of stiffness 0.2kg 0.4kg. 0.8kg and 1.6kg/mm
• a calibrated mask and one set of 50 charts, in a metal carrying case.

Spares & Accessories:

• Chart set of 50 Calibrated mask Spring set comprising one each of stiffness 2n/mm, 8 n/mm and 16 n/mm Coning tool for 38mm sample
• (female) Coning tool for 38mm sample,
• (male) Tripods stand wooden, for using the instrument in field. 

Our Load Frames are used to apply load on the test specimen. The capacity and speed depends on the requirement of a particular test and these are used in C.B.R. triaxial, unconfined compression test. Further, these are Ideal for using mobile laboratory.Load Frame, Motorized, 30 speeds (50 kN) cap.Two Pillar type, Detachable frame, Enclosed motor and gear system, Jewel lamps indicating direction of motion, Speed chart.Consists of a cabinet which housed the gear system & motor with sturdy angle iron frame.The loading is done through the bottom loading platen, which is carried on a lead screw which advances upwards.The top load bracket which slides over two upright pillars, can be positioned at any desired height and locked. It caries a screw adaptor for standard Proving ring. Rate of strains : 30, ( 6 mm/min to 0.00048 mm/min by interchanging the drive and driven gears, another set of 24 rates of strain can be obtained. 220V, 1 Ph, 50 cycles, AC supply.The Loading part of the unit is detachable from the main unit for ease of transport and to avoid damage to the tension rods.

This instrument is used for preparing soil samples for various tests like Triaxial Test, Unconfined Compression Test etc. Soil lathe consist of a cabinet enclosing motor and gear system which rotates a disk at 24 R.P.M. this disc adopts gripper plate of various size. An up right has an adjustable holder and takes upper gripper plates of different diameters. Arrangement is provided to control height and depth of cutting tool through a lead screw which has speeds 0.8mm / min. And 1.6mm / min. Supplied complete with gripper plate pairs for 38mm, 50mm, 75mm, and 100mm dia specimens. 

This is similar to  with the added advantage of a motorized drive permitting a choice of three constant rates of stain.


Specification:

• Comprises a screw operated load frame
• cap.5000kg with a gear box and motor drive giving 1.25, 1.5, 2.5mm/min
• Rates of strain
• a pair of cone seating
• adapter for proving ringand stain dial gauge bracket.
• Supplied with one pair of male/female coning tools for 38mm dia samples but without ring and dial gauge
• Suitable for operation on 230 V, Single Phase A.C. Supply.

 

Accessories:

• Coning tools in pairs (Male & Female) for samples having diameter 38mm, 50mm, 75mm & 100mm.

Consolidation test is un-dimentional test considered extremely important in soil mechanics. Sample taken from adjacent areas of a single site show differential settlement even when tested using same techniques. Soil of similar strength may show varying consolidation. Samples are very carefully prepared and vertical settlement of the specimen in saturated or drained conditions carefully recorded when known load is applied.
Specification:The standard outfit comprises of the following items. Loading unit, maximum capacity 20kg/cm.sq. Having a loading yoke connected to a lever arm with a counter balancing adjustment and having a lever ratio of 1:1 the whole assembly being mounted on a sturdy steel frame stand. The loading unit is so designed that it can be used for consolidation cells of different diameters as well as different dia floating ring type consolidation cells. Fixed ring type Consolidometer (Odeometer) cell assembly for testing 60mm dia x 20mm thick specimen comprising:Fixed ring type Consolidometer (Odeometer) cell assembly for testing 60mm dia x 20mm thick specimen comprising: Fixed ring for specimens 60mm dia x 20mm thick with guide ring. Top and bottom porous stones for 60mm dia specimen. Perforated pressure pad, Channeled base with water inlet and gasket Flanged water jacket, water reservoir with plastic tube and pinch cock. Set of weights to give a pressure of 10kg/cm.sq. On 60mm dia specimen, comprising : 7 nos. 0.05 kg/cm .sq., 5nos. 0.1 kg/sq.cm., 6nos. 0.5kg/sq. cm., and 5 nos. 1.0 kg/sq.cm. Supplied complete as above but without dial gauge. 
Accessories :Dial gauge 0.002 mm x 10mm. Extension piece, 40 mm long, consolidation test forms pad of 50 for one dimensional consolidation. OPTIONAL EXTRAS : Varying head stand pipe, 50cms. Long with mm. Scale. Fixed ring type of Consolidometer (Odeometer) cell assembly for 50mm. dia x 20mm thick specimens , complete with fixed ring guide ring. Pair of porous stones, perforated pressure pad, channeled base, gasket and flanged water jacket. Set of weights to give a pressure of 10kg/sq.cm. on 50cm. dia specimen. Fixed ring type of Consolidometer (Odeometer) cell assembly for 70mm dia x 20mm thick specimens, complete with accessories as above.Set of weights to give a pressure of 10 kg/sq.cm. on 70mm dia specimens. Fixed ring type of consolidometer (Odeometer) cell assembly for 100mm dia x 25mm thick specimens, complete with accessories as above. Set of weights to give a pressure of 10 kg/sq.cm. on 100mm. Dia specimens.

This apparatus is used for the in place determination of the dry density of compact, line and medium grained soils and for layers not exceeding 50cm thickness. The complete apparatus consists

• one each of Small sand pouring cylinder
• 3 litre capacity fitted with conical funnel and shutter
• Cylinder calibrating container
• internal dia 10cm and internal depth 15cm dia hole in the centre.

Accessories:

• Metal tray
• 30cm square and 4cm deep without hole
• Test forms pad of 50.

Note :Sand pouring cylinder medium and large as per IS 2720 (P-XXVIII) also available. 

A very useful kit to determine on the spot soil pH value. This is a compact kit easy to carry on site. CONSISTS OF :12 thick walled test tubes with rubber bungs.1 tube Cleaning brush.1 bottle of Barium Sulfate (100gm)1 bottle of Soil indicator (100gm)1 bottle of Distilled water (500gm)1 Spatula.1 Color chart, range 4.0 to 8.0 PH in 0.5 PH steps.Complete with carrying case. 

The equipment is used for the determination of the relative density of cohesion less free draining soils and meets the essential requirements.
Specification :The equipment consists one each of: Vibratory table, with a cushioned steel vibrating decks about 75cm x 75cm. It has a frequency of approximately 3600 vibratory table, minute under a 11.5kg load. Amplitude is variable in between 0.65mm in step of 0.05 to 0.25mm, 0.25 to 0.45 mm and 0.45 to 0.65mm. Suitable for operations on 415V, Three Phase supply. Cylindrical metal unit weight mould, 3000ml. Capacity.Guide sleeve with clamp assembly. Surcharges base plate for mould. Handle for surcharge base plate. Surcharge weight. The total weight together with surcharge base plate and handle is equipment to 140 kg. /sq. cm. For mould. Cylindrical metal unit weight mould 15000 ml. capacity. (Total weight together with the above mould & surcharge weight is equivalent to 140 kg./sq. cm) dial gauge 0.01mm x 50mm travel. Extension piece 25mm for dial gauge. 

Water trough : Floating ring type of Consolidometer (Odeometer) cell assembly for 60mm dia x 20mm thick specimens complete with floating ring with two guide rings, pair of porous stones, pressure pad and cutting collar. Set of weights to give a pressure of 10kg/cm. sq. on 60mm dia specimens. Floating ring type of Consolidometer (Odeometer) cell assembly for 50mm dia x 20mm thick specimens complete with accessories as above. Set of weights to give a pressure of 10kg/cm. sq. On 70mm dia specimen. Floating ring type of Consolidometer (Odeometer) cell assembly for 100mm dia x 25mm thick specimens complete with accessories as above. Set of weights to give a pressure of 10kg/cm. sq. On 100 mm dia specimen. Additional set of weights for loading up to 20kg/ sq. cm. Set of weights to give a pressure of 10kg / sq. cm. On a 60mm dia specimen comprising 10 off 1.0kg/ sq. cm. Set of weights to give a pressure of 10kg / sq. cm. On a 50mm dia specimen comprising 10 off 1.0kg/ sq. cm. Set of weights to give a pressure of 10kg / sq. cm. On a 70mm dia specimen comprising 10 off 1.0kg/ sq. cm.Set of weights to give a pressure of 10kg / sq. cm. On a 100mm dia specimen comprising 10 off 1.0kg/ sq. cm.Pair of top & bottom porous stones for 50mm dia cell Pair of top & bottom porous stones for 60mm dia cell Pair of top & bottom porous stones for 70mm dia cell Pair of top & bottom porous stones for 100mm dia cell.

Rigidly manufactured from aluminum alloy casting to provide a high degree of accuracy with any frame distorsion under load. The load bridge group is supported in high accuracy self-aligning seat balls. The beam provides three loading ratio: 9:1 10:1 11:1 and the beam assembly is fitted with an adjustable counterbalance weight. Maximum load: 150 kg of slotted weights. The odeometer accepts cells up to 100 cm. sq. Supplied complete with rod holding the weights and coupling block holding the dial gauge or transducer. Supplied 'without': Consolidation cell, Weights, Dial Gauge (or transducer), holding bench which have to be ordered separately. 

The Complete set consists of one each:

• Glass plate 20cm X 15cm having ground ends and one side frosted.
• Brass or stainless steel rod 3mm dia X 150mm long - 2 Nos.
• Flexible spatula.
• Set of 6 moisture containers
• Porcelain basin 150mm dia. Packed in nice polished wooden box.

When conducting traixial tests on soil samples, it is observed that due to internal pressure, the cell expands, soil specimen consolidates resulting in the change of volume. Volume change Gauge is therefore deviced to accurately measure volume changes. This is measured by observing the quantity of water entering or leaving the cell as the cell pressure and axial load are changed it is achieved by the displacement of free surface between the water supplied to the cell and another fluid (paraffin or kerosene). A dye is added to the paraffin for clear demarcation of the interface. The unit consists of a glass graduated tube of the appropriate capacity graduated to parts of a ml.enclosed in a perspex tube sealed by two end caps. The unit is fitted with manifolds and valves which enables it to be used with the triaxial cell and the constant Pressure (Mercury controls) system. The cell pressure can either be directly applied to the cell from the constant pressure system or through the volume change gauge. The graduated glass tube is not subjected to any difference in pressure and its inside is coated with a layer f silicon water repellent to reduce the error in meniscus. There is an arrangement for filling the unit with water and paraffin and a drainage valve is provided in the lower end cap. The whole assembly is mounted on a panel suitable for wall mounting. The unit is supplied complete with a pressure hose with end couplings and a packet of dye.

It is a light weight aluminum derrick can be dismalted for ease of transport. The equipment is suitable for shallow soil sampling, lifting casing, standard penetration tests and lifting operations. Complete with upper tie bolt and ball but without sheave.

Specification :

• Comprises hydraulic proctor needle system complete with a pressure gauge fixed at easily readable angle reading 0-70 kg x 2 kg
• A set of needle points consisting one each 0.25, 0.5, 1.0, 1.5, 2.0, 3.5 and 6.0 sq. cm.
• a wooden carrying case. 

Soil Testing Kit is Development for extension purpose. The result can be used advantageously for soil fertility evaluation and fertilizer recommendation. The whole idea of soil testing is based on the efficient farming practice. The efficient use of fertilizer is directly related to the knowledge of what nutrients, the soil lacks.

Parameters:

•  pH
•  Chloride
•  Sulphate
•  Carbonate & Bicarbonate
•  Magnesium
•  Phosphate
•  Nitrate
•  Iron
•  Potassium
•  Ammonical salt & Nitrogen 

Used to determine the moisture content at which clay soils pass from a plastic to a liquid state. Two Version are available. One the standard one & the other is semi-automatic with timer where the cone is allowed to free fall for a period of 5 seconds including one each of 50 gm. & 100 gm. weight, one penetration cone, preset counter & measuring cup. 

The unit provides a constant uniform shaking with automatic cycle test. Oscillating excursion is 200 mm at 175 strokes / minute rate. Complete with timer that automatically stops the shaker at the end of the test. Power Supply 230 V A.C. 50Hz. 

For specimen size 38mm x 76mm long comprises. Split mould 38mm dia x 126mm long. End plug 38mm dia x 25mm long pair. Split collar interchangeable. Ejecting plunger 38mm dia x 126mm long.

ACCESSORIES :

• Split mould 38mm dia x 76mm long and split mould 38mm dia x 86mm long.

A simple mould which is filled with the soil under test. This is then dried and the resulting decrease os length of the specimen measured is expressed as the linear shrinkage. It is 25mm Dia. x 12.5mm Height x 140mm Length. 

Instead of a set of three glass stand pipes a stand with nine glass tubes of 6mm, 10mm, 20mm, 25mm, 40mm, 50mm, 60mm, 70mm, 75mm, bore tube is provided with over flow arrangement for constant head tests. The remaining tubes are used for falling head test. 

This is for mechanical analysis and also other laboratory applications for stirring speed approximately 4000 R.P.M. under load. A dispersion cup is supported on a rest on the stand of the stirrer and has a removable baffle. For operation on 230V A.C. supplied with dispersion cup or baffle cup. 

This cone is used to find out viscosity of bentonite slurry and similar material. The marsh cone is 6 inch in diameter at the top and 12 inch long, and tapers to join a tube 2 inch long and 3/16 inch inside dia. The capacity of the funnel is 1500cc. Time in seconds required to flow out 1000cc of slurry from cone is measured as funnel viscosity of the material. 

The equipment consists one each of the following : Load frame, hand operated , capacity 5000 kg. With high and low rates of travel of the lead screw. Mould made from gun metal/brass, 150mm internal dia x 175mm high, with perforated base plate and extension collar 50mm high. Penetration piston, face dia 50mm with adjustable bracket for penetration dial gauge. Circular metal space disc, 148mm dia x 47.7mm high. With detachable handle. Annular metal weight, 2.5 kg. 147 mm dia with 53 mm dia central hole. Slotted metal weight, 2.5kg. 147mm dia with 53 dia slot. Perforated plate made of gun-metal/brass 148mm dia with adjustable stem and lock nut and a metal tripod for dial gauge. Cutting collar, Rammer 2.6kg weight with drop of 310mm. Rammer 4.89 kg. with drop of 450mm.Supplied with proving ring and dial gauge.

1 Bristle round brush 30 mm.                                 
2 Nylon sieve brush 33 mm.                                  
3 Soft Hair brush 3 mm dia.                                   
4 Double ended brass & nylon bristle.          
5 Double ended nylon sieve brush.

The cell is useful for testing 38mm dia x 76mm high soil specimen. Transparent Perspex chamber with anvil and loading plunger, the cell is easily opened by releasing four nuts of the tie rods. It is leak proof up to 10kg/cm.sq. Fluid pressure. An oil plug which can also be used as an air vent is provided for introducing a thin layer of oil over water. This provides effective sealing at the plunger for long duration tests. The cell is fitted with four sleeve packed valves of no volume change type on the base. These valves are used for cell pressure, pore water pressure, drainage or back pressure. The loading plunger of the cell has dial gauge rest. Loading pad made of Perspex for 38mm dia specimens. Pair of plain discs made of Perspex 38mm dia 6mm thick. Pair of porous stones 38mm dia specimen. Split sand former for 38mm dia specimen. Sheath stretcher for 38mm dia specimen. One dozen rubber sheaths for 38mm dia samples. For synthetic rubber 'o' rings for 38mm dia specimen. One plastic drainage tube. 

Shrinkage limit is the maximum water content at which a reduction in water content does not cause an appreciable reduction in volume of the Soil Mass. At shrinkage limit, on further reduction in water, air enters in to the voids of soils and thus keeps the volume constant. The apparatus can be used to determine shrinkage limit and to calculate other shrinkage ratio, shrinkage index and volumetric shrinkage.

Specification :Set consists of one each :-1. Porcelain evaporating dish2. Shrinkage dish3. Glass cup4. Perspex plate with three metal prongs5. Flexible spatula 100mm6. Glass cylinder7. 25ml x 1ml, supplied without mercury
Optional Accessories:Mercury supplied in bottle of 500 gms. at an extra cost.

Shrinkage Limit is the maximum water content at which a reduction in water content does not cause an appreciable reduction in volume of the soil mass. At shrinkage limit, on further reduction in water, air enters into the voids of soils and thus keeps the volume constant. The apparatus can be used to determine shrinkage limit and to calculate other shrinkage factors like shrinkage ratio, shrinkage index and volumetric shrinkage.
Salient Features Specifications : Set consists of one each :- 1. Porcelain evaporating Dish. 2. Shrinkage Dish 3. Glass Cup. 4. Perspex plate with three metal prongs 5. Perspex plate. 6. Flexible spatula 7. Glass cylinder 25ml x 0.5mlsupplied without mercury.

The drive is by means of a rack and pinion manually through a gearing arrangement. The gear box and pinion are fixed on two handles, sprockets and chain arrangement. The movement of the rack is guided by a bracket ( attached to the rack) and two pillars. The penetration resistance i.e. the pressure is indicated on hydraulic gauges through a hydraulic measuring head. Two pressure gauges of 15cm dia dial and 2 capacities 0-160kg/cm are provided. An automatic cut-off valve, to protect the low capacity gauge from being overloaded is provided. The 2 valve can be adjusted and locked at desirable values between 20 to 60cm . A provision is made to anchor the unit to the ground (with the help of four anchors supplied with the unit) and there is a provision for lateral 2 movement of the unit so that subsequent tests could be performed without shifting the entire anchorage. A 10cm penetration cone with friction jacket is provided along with fifteen mantle tubes (non-uniform having an effective length of 1 m each with sounding rods for finding out the cone (point) resistance or jacket friction. 

For reaching greater depths and to facilitate easy and constant rate of penetration 1 to 2.5cm/sec of the cone this engine-driven Static Cone Penetrometer of 100 KN (10,000 Kgf) capacity is preferable. The equipment consists of a hydraulic pump driven by a Diesel Engine. The whole system is mounted on a tow able trolley fitted with pneumatic wheels. The pumping unit and ram are connected by means of flexible pipes through a direction control valve. The hydraulic ram moves on a two pillar stand mounted on a trolley 1.Penetration Cone, steel 60 cone angle, 10cm2 base area, with friction jacket One 2. Mantle Tube, 36mm uniform OD with sounding Rod working length 1 m Thirty                               3. Load Measuring Head, with Automatic cut-off valve, and oil can without pressure gauges. 4. Pressure Gauge, 0-600 x 5 kg/cm One 5. Pressure Gauge, 0 100 x 1kg/cm One 6. Trusses Two 7. Screw Anchor 45 cm Six 8. Screw Anchor 30 cm Six 9. Screw Anchor 20 cm Six 10. Screw Anchor Rod with cone Six 11. Driving handle for Screw Anchor One 12. Extension Pipe for Handle Four              13. Clamping Screw with Nuts Six 14. Extractor Tube with Connector One 15. Tool Box One                 16. Tarpaulin Cover One.

Used to determine the in-situ density of fine grained compacted soil. The test consist in digging a hole into the ground and then collect, dry and weight the sampled soil. The hole is then filled with dry sand from the cone container. The apparatus consist of a double metal cone, one plastic 5 lts jar & a metal tray with centre hole. Size of the cone is 6½” (165.1mm)
Note:On request 12” (305 mm) Sand Density Cone Apparatus is also supplied at an extra cost. 

For determining the liquid limit of soils. This is specially useful to obtain reliable and accurate results of those soil which have low plasticity index. The percentage moisture contents determined when cone with half angle of 15-30 minutes under a total sliding weight of 148 gm penetrates 25mm gives the liquid limit. 

Useful to determine specific gravity of clays, sand and gravel of size smaller than 10mm. Specification :Comprises a 1 kg. glass jar with brass cone. Locking ring and rubber seal.
Spare: Rubber seal. 

For reaching greater depths and to facilitate easy and constant rate of penetration 1 to 2.5cm/sec of the cone this engine-driven Static Cone Penetrometer of 100 KN (10,000 Kgf) capacity is preferable. The equipment consists of a hydraulic pump driven by a Diesel Engine. The whole system is mounted on a tow able trolley fitted with pneumatic wheels. The pumping unit and ram are connected by means of flexible pipes through a direction control valve. The hydraulic ram moves on a two pillar stand mounted on a trolley 1.Penetration Cone, steel 60 cone angle, 10cm2 base area, with friction jacket One 2. Mantle Tube, 36mm uniform OD with sounding Rod working length 1 m Thirty 3. Load Measuring Head, with Automatic cut-off valve, and oil can without pressure gauges. 4. Pressure Gauge, 0-600 x 5 kg/cm One  5. Pressure Gauge, 0 100 x 1kg/cm One 6. Trusses Two 7. Screw Anchor 45 cm Six                     8. Screw Anchor 30 cm Six 9. Screw Anchor 20 cm Six 10. Screw Anchor Rod with cone Six                     11. Driving handle for Screw Anchor One 12. Extension Pipe for Handle Four 13. Clamping Screw with Nuts Six 14. Extractor Tube with Connector One 15. Tool Box One 16. Tarpaulin Cover One.